Home
Главная
Makita
Гайковерты
DTD170Z без акк. и з.у
Инструкция по эксплуатации Страница: 7

Makita DTD170Z без акк. и з.у [7/60] A mode

7 ENGLISH

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Switch action

►Fig.5: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

To start the tool, simply pull the switch trigger. Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

NOTE: The tool automatically stops if you keep pull-

ing the switch trigger for about 6 minutes.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.6: 1. Lamp

►Fig.7: 1. Button

Pulltheswitchtriggertoturnonthelamp.Toturnoff,

release it. The lamp goes out approximately 10 seconds

after releasing the switch trigger.

To keep the lamp off, turn off the lamp status. To turn off

thelampstatus,rstpullandreleasetheswitchtrigger.

Andthenpressthebutton

within 10 seconds.

To turn on the lamp status again, press the but-

ton

again similarly.

NOTE:Toconrmthelampstatus,pullthetrigger.

Whenthelamplightsupbypullingtheswitchtrigger,

thelampstatusisON.Whenthelampdoesnotcome

on, the lamp status is OFF.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Reversing switch action

►Fig.8: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

Whenthereversingswitchleverisintheneutralposi-

tion, the switch trigger cannot be pulled.

A mode

“Amode(assistmode)”isaneasy-to-usemodefor

driving screws with good control.

In this mode, the tool drives a screw with low-speed

rotationatrst.Afterthetoolstartstoimpact,therota-

tion speed increases and reaches the maximum speed.

ToturnonAmode,pressthebutton

on the panel.

PulltheswitchtriggertostartdrivinginAmode.

►Fig.9: 1. Button 2. Button

ToreleaseAmode,pressthebutton (not the but-

ton ).

Changing the impact force

►Fig.10: 1.Changedinvesteps2. Max 3. Hard

4. Medium 5. Soft 6. T mode 7. Button

Youcanchangetheimpactforceinvesteps:max-

,hard, medium, soft, and T mode.

This allows a tightening suitable to the work.

Everytimethebutton is pressed, the number of

blowschangesinvesteps.

“T”isaspecialmodeforfasteningselfdrillingscrews.

In this mode, the tool starts to drive a screw with faster

rotation, which is suited for drilling with the self-drilling-

screw tip. Once the tool starts to tighten the screw, it

impacts in medium force grade.

For approximately one minute after releasing the switch

trigger, the impact force can be changed.

Makita DTD170Z без акк. и з.у [7/60] A mode

Содержание

Похожие устройства