Einhell PXC AXXIO (4431140) без акк. и з.у Инструкция по эксплуатации онлайн [22/42] 672464

- 22 -

6.4 Changing the grinding wheels (Fig. 8/9)

Use the face spanner (5) supplied to change the

grinding wheels. The face spanner (5) is stored in

the additional handle (3). Pull the face spanner (5)

out of the additional handle (3) when you need it.

Danger! For safety reasons, the angle grinder

must not be operated with the face spanner (5)

inserted in it.

•

Simple wheel change by spindle lock:

•

Press the spindle lock and allow the grinding

wheel to latch in place.

•

Open the flange nut with the face spanner.

(Fig. 9)

•

Change the grinding or cutting wheel and

tighten the flange nut with the face spanner.

Notice!

Only ever press the spindle lock when the

motor and grinding spindle are at a stand-

still! You must keep the spindle lock pressed

while you change the wheel!

For grinding or cutting wheels up to approx. 3 mm

thick, screw on the ﬂ ange nut with the ﬂ at side

facing the grinding or cutting wheel.

6.5 Flange arrangements when using grin-

ding wheels and cutting wheels (Fig. 10-

13)

•

Flange arrangement when using a de-

pressed-centre or straight grinding wheel

(Fig. 11)

a) Clamping flange

b) Flange nut

•

Flange arrangement when using a de-

pressed-centre cutting wheel (Fig. 12)

a) Clamping flange

b) Flange nut

•

Flange arrangement when using a straight

cutting wheel (Fig. 13)

a) Clamping flange

b) Flange nut

6.6 Motor

It is vital for the motor to be well ventilated during

operation. Be sure, therefore, to keep the ventilati-

on holes clean at all times.

6.7 Grinding Wheels

•

Never use a grinding or cutting wheel bigger

than the specified diameter.

•

Before using a grinding or cutting wheel,

check its rated speed.

•

The maximum speed of the grinding or cut-

ting wheel used must be higher than the idle

speed of the angle grinder.

•

Use only grinding and cutting wheels that are

approved for a minimum speed of 8,500 rpm

and a peripheral speed of 56 m/sec.

•

Check the direction of rotation when you use

diamond cutting wheels. The directional arrow

on the diamond cutting wheel must point in

the direction in which the tool rotates.

Warning!

Take special care that the grinding/sanding

wheels are properly stored and transported.

Ensure that the grinding/sanding wheels are

never exposed to shock, jolts or sharp edges (for

example during transport or storage in a toolbox).

This could cause damage (such as cracks) to the

grinding/sanding wheels and place the user in

serious danger.

Warning!

6.8 Operating Modes

6.8.1 Rough grinding (Fig. 14)

Caution: Use the safety device for sanding/

grinding (included in items supplied).

For the best rough grinding results, hold the grin-

ding wheel at an angle of between 30° and 40° to

the workpiece surface and guide back and forth

over the workpiece in steady movements.

6.8.2 Cutting (Fig. 15)

Caution: Use the safety device for abrasive

cutting (available as accessory, see 7.3)

When you use the right-angle grinder for cutting

purposes, avoid tilting it in the cutting plane. The

cutting wheel must have a clean cutting edge.

A diamond cutting wheel is best used to cut hard

stone.

Warning!

It is prohibited to use the machine on asbes-

tos materials!

Warning!

Never use a cutting wheel for rough grinding.

Anl_TE_AG_18_125_Li_BL_SPK9.indb 22Anl_TE_AG_18_125_Li_BL_SPK9.indb 22 24.04.2018 13:47:1724.04.2018 13:47:17

Einhell PXC AXXIO (4431140) без акк. и з.у Инструкция по эксплуатации онлайн [22/42] 672464

Содержание

Похожие устройства