![Zotek ZT-TC13 [10/24] Using instruction](/img/pdf.png)
Zotek ZT-TC13 [10/24] Using instruction
![Zotek ZT-TC13 [10/24] Using instruction](/views2/1893303/page10/bga.png)
6. Using instruction
(1) Single point test:
a. Short press button to turn it on, it will
calibrate automatically, it will enter into single
point test mode by default , check the
following picture:
b. Now, the single point mode measurement can
be carried out, and the meter can
automatically judge whether the measured is
Fe or NFE substrate, and the displayed unit is
μm by default. check the following picture:
8
Содержание
- Coating thickness gauge 1
- User manual 1
- Negligence misuse modification pollution and 2
- Preface 2
- Statement 2
- Contents 3
- Electrical specifications 21 3
- Product features 3 3
- Electromagnetic induction and eddy current measurement 4
- Manufacturing sales evaluation metal processing 4
- Summary 4
- Using the eddy current of non magnetic metal substrate 4
- 1 the measurement method is in accordance with gb 5
- 3 the thickness of non magnetic coating on magnetic 5
- Product features 5
- Whether the current measured value exceeds the limit 5
- Which has the characteristics of precision wear 5
- Accessary check 6
- Main meter 6
- Sensor protective cover one use to cover on the 6
- Precautions 7
- Proximity sensor ring 7
- Section of the manual 7
- Solvent to prevent the shell from being corroded and 7
- Accessory which is related to the accuracy of the 8
- Properly preserved to prevent its surface from scratch 8
- Menu enter button 9
- Product functions instruction 9
- Using instruction 10
- Please refer to the introduction of unit settings later 11
- The point 12
- Minimum values of the measurement can be displayed 13
- At this time it will prompt that the stored data 15
- Short press to enter in menu page 15
- B upper limit must be bigger than lower limit 17
- E voice setting 18
- Enter into page and choose unit 18
- F language setting 18
- Button to enter into calibration mode 19
- Attention if the value of the supplied diaphragm 20
- Confirm when press confirms the calibration 21
- Continue and the operation method is the same as 21
- When the calibration step jumps to the interface 21
- In the menu interface press or 22
- A before or during the use of the product the low battery prompt interface will pop up on the 23
- B after the battery is installed always cover the 23
- Battery cover and tighten the screw in clockwise 23
- Electrical specifications 23
- Replace battery 23
- Screen at this time use a suitable screwdriver 23
- Screen flip manual setting 0 90 180 270 4 directions 23
- Turn the screw in counterclockwise open the battery cover and install two new aaa batteries according to the indication in the battery compartment 23
Похожие устройства
- Zotek ZT-DB02 Инструкция по эксплуатации
- Oxgard Praktika T-05-SMK-900 Инструкция по монтажу
- Oxgard Praktika T-06-CM-660 Инструкция по монтажу
- Oxgard Praktika T-06-CM-900 Инструкция по монтажу
- Oxgard Praktika T-06-CMK-660 Инструкция по монтажу
- Oxgard Praktika T-06-CMK-900 Инструкция по монтажу
- Oxgard Praktika T-06-GCM-660/900 Инструкция по монтажу
- Oxgard Praktika T-06-GCMK-660/900 Инструкция по монтажу
- Oxgard Praktika T-06-SM-660 Инструкция по монтажу
- Oxgard Praktika T-06-SM-900 Инструкция по монтажу
- Oxgard Praktika T-06-SMK-660 Инструкция по монтажу
- Oxgard Praktika T-06-SMK-900 Инструкция по монтажу
- Oxgard Praktika T-10 Инструкция по монтажу
- Oxgard Praktika T-10 Double Pass Инструкция по монтажу
- Oxgard Praktika T-10-G Инструкция по монтажу
- Oxgard Praktika T-10-G Double Pass Инструкция по монтажу
- Oxgard Praktika T-10-GM Инструкция по монтажу
- Oxgard Praktika T-10-GM Double Pass Инструкция по монтажу
- Oxgard Praktika T-10-H Инструкция по монтажу
- Oxgard Praktika T-10-H Double Pass Инструкция по монтажу