Home
Главная
VTS
Водяной Насос
WPG - 25-095 - 16
Инструкция по эксплуатации Страница: 1

VTS WPG - 25-095 - 16 Инструкция по эксплуатации онлайн

VTS WPG - 25-095 - 6.3 Инструкция по эксплуатации онлайн

Water pump group

Technical documentation

WPG-v.1.0 (03.2016)

Содержание

Water pump group 1
Contents 2
Application and design 3
Introduction 3
Additional information for the elements of the group can find in the suppliers manuals table pump types used in the pump group 5
Table technical data 5
Technical parameters table dimension and connection diameter 5
Fig characteristics of water pump groups 6
Pump groups characteristic the below characteristic concerning to the clean water the pumps groups may be used in heating systems containing glycol based anti freeze with corrosion inhibitors up to a maximum of 35 solution depending on the type of glycol the mixture and the liquid temperature the viscosity will increase with water as medium this will influence the pressure loss of the system as well as the efficiency performance and load of the pump 6
Wpg 25 105 6
Wpg 25 70 6
Wpg 25 95 6
Installation 7
Display indication pump operation counter action 10
Operation and maintenance 10
Push button leds 10
Start up of the pump do not start the pump until the system has been filled with liquid and vented being self venting the rotor can does not require venting before start up air inside the pump will be transported by the medium into the system during the first minutes after pump start up the system cannot be vented through the pump as the pump is self venting it does not need to be vented before start up however besides the smallest pump 25 70 it is recommended to vent pumps installed in systems where the pumped medium is very dirty as well as after service of the pump the screw may be loosened to check if the system has been vented completely 10
The operation of the pump depend on the type used in the water pump group table the operation of the pump depend on the type used in the water pump group table upm3 25 70 flex as 10
The user interface is designed with a single push button one red green led and four yellow leds 10
The user interface shows performance view during operation operation status alarm status settings view after pressing the button during operation the display shows the performance view if you press the button the user interface switches the view or runs in the setting selection mode the performance view shows either the operation status or the alarm status when the circulator is running led 1 is green the four yellow leds indicate the current performance as the percentage of p max 0 one led green 0 25 one led green one yellow 25 50 one led green two yellow led and adequately for 50 75 75 100 when the operation mode is active all active leds are constantly on in order to differentiate this mode from the select setting mode if the circulator is stopped by an external signal led 1 flashes green alarm status if the circulator has detected one or more alarms the bi colored led 1 switches from green to red when an alarm is active the leds indicate the alarm type as defined in the table below 10
When loosening the air venting de blocking screw be aware of hot spraying water when loosening the air venting de blocking screw be aware of hot spraying water 10
Factory presetting 11
Fast proportional pressure slow constant pressure power after ten seconds not pushing the button setting is adapted pump returns to operating mode led 1 or 2 or 3 is permanently on pump is running with the selected curve and mode 11
For detailed information refer to the pump supplier documentation maintenance of the pump group comes to periodic checking and cleaning of strainer filter 11
Key lock function the purpose of the key lock function is to avoid accidental change of settings and misuse when the key lock function is enabled all long key presses will be ignored this prevents the user from entering the select setting mode area and allows the user to see the show setting mode area if you press the key lock for more than 10 seconds you can toggle between enabling disabling the key lock function when doing so all leds except for the red led will flash for a second indicating that lock is toggled 11
Led 1 led 2 led 3 led 4 led 5 11
Led indication of the curve setting cp and pp curves 11
Proportional pressure curve pp2 push the button for two seconds pump goes to setting mode led starts flashing with each push the setting changes led 1 2 3 are permanently on and then the control curve and mode is changed flashing mode 11
Settings view you can switch from the performance view to the settings view by pressing the push button the leds indicate the actual setting the settings view shows which mode controls the circulator no settings can be made at this stage after 2 seconds the display switches back to performance view if led 1 is green it indicates operation or internal control if led 1 is red it indicates alarm or external control led 2 and 3 indicate the different control modes and led 4 and 5 indicate the different speeds 11
The user interface allows to select between 6 control curves in two control modes three proportional pressure curves pp three constant pressure power curves cp 11
Upml 25 95 auto and upmxl 25 105 auto 11
It is forbidden to place dispose of and store worn out electric and electronic equipment together with other waste dangerous compound contained in electronic and electric equipment have a very adverse impact on plants micro organisms and most importantly on humans as they damage our central and peripheral nervous system as well as circulatory and internal system additionally they cause serious allergic reactions worn out equipment is to be delivered to a local collection point for used electric equipment which carries out a selective collection of waste remember the user of equipment intended for households and which has been worn out is obliged to transfer such equipment to a collecting unit that collects worn out electric and electronic equipment the selective collecting and further processing of waste from households contributes to the protection of environment reduces the penetration of hazardous substances into the atmosphere and surface waters 12
The pump does not require any maintenance during service life since pump bearings are water lubricated it is recommended that the pump be switched on for a few minutes each week whenever the system is not in use to prevent sediment build up in the pump if the pump has been inoperative for a long period i e during summer season it is advisable to check the pump shaft for free rotation before switching on close isolating valves and unscrew and remove the vent plug locate a small screwdriver 3 mm into the end of the shaft push gently and rotate several times in each direction close vent plug and retighten fault finding 12
Electric installation 16
Instalacja elektryczna 17
Elektroinstalācija 18
Elektripaigaldis 19
Elektromos telepítés 20
Electrické zapojení 21
Elektros instaliacija 22
Warranty card 23
Karta gwarancyjna 24
Garantijas karte 25
Garantiikaart 26
Garanciapapír 27
Záruční list 28
Garantinė kortelė 29

Похожие устройства