Град-М ПД-160 [12/24] Warning

Град-М ПД-160 [12/24] Warning
16
saw to jump backwards, but kickback forces can be
controlled by the operator, if proper precautions are
taken)
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to
a complete stop; never attempt to remove the saw
from the work or pull the saw backwards while the
blade is in motion or kickback may occur (investi-
gate and take corrective actions to eliminate the cause
of blade binding; avoid cutting nails or screws)
When restarting a saw in the workpiece, centre
the saw blade in the kerf and check that saw teeth
are not engaged into the material (if saw blade is
binding, it may walk up or kickback from the workpiece
as the saw is restarted)
Support large panels to minimize the risk of
blade pinching and kickback (large panels tend to
sag under their own weight; supports must be placed
under the panel on both sides, near the line of cut and
near the edge of the panel)
Do not use a dull or damaged blade (unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback)
• Blade depth and bevel adjusting locking levers
must be tight and secure before making cut (if blade
adjustment shifts while cutting, it may cause binding
and kickback)
Use extra caution when making a plunge cut into
existing walls or other blind areas (the protruding
blade may cut objects that can cause kickback)
WARNING
Check lower guard for proper closing before
each use
Do not operate the saw if lower guard does not
move freely and close instantly
Never clamp or tie the lower guard into the open
position
If saw is accidentally dropped, lower guard may be
bent; raise the lower guard with the retracting handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut
Check the operation of the lower guard spring; if
the guard and the spring are not operating properly,
they must be serviced before use (lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a build-up of debris)
Lower guard should be retracted manually only
for special cuts such as plunge cuts and compound
cuts; raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released (for all other sawing, the lower guard
should operate automatically)
Always observe that the lower guard is covering
the blade before placing saw down on bench or
oor (an unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path;
be aware of the time it takes for the blade to stop after
switch is released)
Avoid damage that can be caused by screws, nails
and other elements in your workpiece; remove them
before you start cutting
When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
Use completely unrolled and safe extension cords
with a capacity of 16Amps (U.K. 13Amps)
In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
Flawless functioning of the tool can be guaranteed
only when original accessories are used
Use only accessories with an allowable speed
matching at least the highest no-load speed of the tool
Never use the tool without the original protection
guard system
This tool should not be used by people under the age
of 16 years
The noise level when working can exceed 85 dB(A);
wear ear protection
If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect the
plug
Never use tool when cord is damaged; have it
replaced by a quali ed person
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
This tool is not suitable for wet cutting
After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
Never use circular saw blades made of high speed
steel (HSS)
Never use grinding/cutting discs with this tool
• Do not work materials containing asbestos
(asbestos is considered carcinogenic)
Take protective measures when during work
dust can develop that is harmful to one’s health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/
chip extraction when connectable
Do not attempt to cut extremely small workpieces
Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
Do not work overhead with the tool
Only use a saw table provided with a switch that
prevents restarting of the motor after interruption of
voltage
Always disconnect plug from power source
before making any adjustment or changing any
accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
ONLY):
Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
If for any reason the old plug is cut off the cord of
this tool, it must be disposed of safely and not left unat-
tended
Your machine is double insulated in accord-
ance with EN 50144; therefore no earthwire is
required.

Содержание

Похожие устройства

Скачать