![Graco Reactor E-20 FH9030 — руководство по ручному управлению текущими настройками [28/42]](/img/pdf.png)
Graco Reactor E-20 FH9030 — руководство по ручному управлению текущими настройками [28/42]
Превью страниц
Страница 28 /
42
![Graco Reactor E-20 CH9025 [28/42] Set pressure](/views2/1900104/page28/bg1c.png)
Operation
28 312065V
10. Manual current control mode only:
a. If FTS is disconnected or display shows
diagnostic code E04, turn main power switch
OFF then ON to clear
diagnostic code and enter manual current
control mode. display will show current
to hose. Current is not limited by target
temperature.
b. Press or to adjust current setting.
c. To prevent overheating, install hose
thermometer close to gun end, within operator
view. Insert thermometer through foam cover of
A component hose so stem is next to inner tube.
Thermometer reading will be about 20°F less
than actual fluid temperature.
d. If thermometer reading exceeds 160°F (71°C),
reduce current with key.
Set pressure
1. Press .
2. Press motor . Motor and pumps start. Display
shows system pressure. Motor runs until setpoint is
reached.
3. Press or until display shows desired
fluid pressure. Display will show setpoint for 10
seconds, then change to actual pressure.
NOTE: If display pressure is greater than setpoint
pressure, trigger gun to reduce pressure.
NOTE: If display shows J xx, unit is in jog mode. To exit
jog mode, see page 33.
4. To display cycle count, press .
NOTE: To clear counter, press and hold for 3
seconds.
5. Press or to change pressure scale.
When in manual current control mode, monitor hose
temperature with thermometer. Install per instructions
below. Thermometer reading must not exceed 160°F
(71°C). Never leave machine unattended when in
manual current control mode.
PSI
BAR
ON / OFF
PARK
Motor Controls and Indicators, see page 17
PSI
BAR
Содержание
129- Not approved for use in explosive atmospheres or hazardous classified locations
- Important safety instructions
- For spraying polyurethane foam and polyurea coatings for professional use only
- Electric heated plural component proportioner
- Operation
- Contents
- Systems
- Total system watts based on maximum hose length for each unit
- Models
- Maximum flow rate given for 60 hz operation for 50 hz operation maximum flow rate is 5 6 of 60 hz maximum flow
- Full load amps with all devices operating at maximum capabilities fuse requirements at various flow rates and mix chamber sizes may be less
- E xp2 series
- E xp1 series
- E 30 series
- E 20 series
- E 20 and e xp1 series 210 ft 64 m maximum heated hose length including whip hose e 30 and e xp2 series 310 ft 94 m maximum heated hose length including whip hose
- Approvals
- Supplied manuals
- Related manuals
- Danger
- Warnings
- Warning
- Warning
- Warning
- Warning
- Isocyanate conditions
- Important isocyanate iso information
- Moisture sensitivity of isocyanates
- Material self ignition
- Keep components a and b separate
- Foam resins with 245 fa blowing agents
- Changing materials
- Typical installation with circulation
- Shown exposed for clarity wrap with tape during operation
- Typical installation without circulation
- Shown exposed for clarity wrap with tape during operation
- Component identification
- Temperature controls and indicators
- Red stop button
- Main power switch
- Temperature scale keys leds
- Temperature displays
- Temperature arrow keys
- Target temperature key led
- Heater zone on off keys leds
- Circuit breakers
- Actual temperature key led
- Pressure key led
- Park key led
- Motor on off key led
- Motor controls and indicators
- Cycle count key led
- Psi bar keys leds
- Spray adjustments
- Pressure cycle display
- Pressure arrow keys
- Locate reactor
- General equipment guidelines
- Table 1 electrical requirements kw full load amps
- Grounding
- Electrical requirements
- Connect pressure relief lines
- Connect feed pumps
- Connect electrical cord
- Install fluid temperature sensor fts
- Connect heated hose
- Supply wet cups with throat seal liquid tsl
- Flush the equipment
- Pressure relief procedure
- Operation
- Startup
- Load fluid with feed pumps
- Set temperatures
- Set pressure
- Table 2available pressure imbalance settings
- Spraying
- Change pressure imbalance setting optional
- Shutdown
- Fluid circulation
- Circulation through reactor
- Circulation through gun manifold
- Jog mode
- To clear
- Alarms turn off motor and heat zones turn main power
- These alarms turn off heat e99 clears automatically when communication is regained codes e03 through
- Alarms
- There are two types of motor control codes alarms and warnings alarms take priority over warnings
- Then on
- Temperature control diagnostic codes appear on temperature display
- Temperature control diagnostic codes
- See repair manual for corrective action
- Reactor will continue to run press to clear an error will not recur for a predetermined amount of time varies for different warnings or until main power is
- Note for hose zone only if fts is disconnected at startup display will show hose current 0a
- Note alarms can also be cleared except for code 23
- Motor control diagnostic codes e21 through e29 appear on pressure display
- Motor control diagnostic codes
- Errors
- E06 can be cleared by pressing for other codes
- Turned off
- Diagnostic codes
- Turn main power off
- By pressing
- Maintenance
- Fluid inlet strainer screen
- Pump lubrication system
- Return tube kit
- Heated whip hoses
- Heated hoses
- Fusion spray gun
- Feed pump kits
- Data reporting kit
- Conversion kit
- Circulation kit
- Air supply kit
- Accessories
- Dimensions
- Technical specifications
- Electric reactor proportioning system
- Electric reactor proportioning system
- Warning cancer and reproductive harm www p65warnings ca gov
- California residents
- California proposition 65
- Www graco com revision
- June 2020
- Graco standard warranty
- Graco information
- Graco inc and subsidiaries p o box 1441 minneapolis mn 55440 1441 usa copyright 2020 graco inc all graco manufacturing locations are registered to iso 9001
- Graco headquarters minneapolis international offices belgium china japan korea
- For the latest information about graco products visit www graco com for patent information see www graco com patents to place an order contact your graco distributor or call to identify the nearest distributor phone 612 623 6921 or toll free 1 800 328 0211 fax 612 378 3505
Похожие устройства
-
Graco REACTOR 2 H-50 PHH156Техническая документация -
Graco REACTOR 2 H-50 PHH156Сертификат -
Graco REACTOR 2 H-50 PHH156Брошюра -
Graco REACTOR 2 H-50 PHH156Инструкция по эксплуатации -
Graco REACTOR 2 H-50 PHH153Техническая документация
-
Graco REACTOR 2 H-50 PHH153Сертификат
-
Graco REACTOR 2 H-50 PHH153Брошюра
-
Graco REACTOR 2 H-50 PHH153Инструкция по эксплуатации
-
Graco REACTOR 2 H-50 PHH056Техническая документация
-
Graco REACTOR 2 H-50 PHH056Сертификат
-
Graco REACTOR 2 H-50 PHH056Брошюра
-
Graco REACTOR 2 H-50 PHH056Инструкция по эксплуатации
Узнайте, как правильно использовать ручной режим управления текущими настройками. Следуйте инструкциям по установке термометра и регулировке давления для безопасной работы.