![Gigabyte B760M AORUS ELITE AX [7/39] 3 box contents](/img/pdf.png)
Gigabyte B760M AORUS ELITE AX [7/39] 3 box contents
![Gigabyte B760M AORUS ELITE AX [7/39] 3 box contents](/views2/1918732/page7/bg7.png)
- 7 -
1-3 Box Contents
5 B760M AORUS ELITE AX, B760M AORUS ELITE,
B760M AORUS ELITE AX DDR4, or B760M AORUS ELITE DDR4 motherboard
5 User's Manual
5 One antennajl
5 Two SATA cables
* The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
j Only for B760M AORUS ELITE AX.
l Only for B760M AORUS ELITE AX DDR4.
Содержание
- B760m a elite ax ddr4 1
- B760m a elite ddr4 1
- B760m aorus elite ax b760m aorus elite 1
- B760m aorus elite ax ddr4 1
- B760m aorus elite ddr4 1
- User s manual 1
- Copyright 2
- Disclaimer 2
- Identifying your motherboard revision 2
- Chapter 1 product introduction 3
- Chapter 2 hardware installation 3
- Chapter 3 bios setup 1 3
- Chapter 4 installing the operating system and drivers 3 3
- Chapter 5 appendix 5 3
- Table of contents 3
- 1 motherboard layout 4
- B760m aorus elite 4
- B760m aorus elite ax 4
- Chapter 1 product introduction 4
- J only for b760m aorus elite ax 4
- B760m aorus elite ax ddr4 5
- B760m aorus elite ddr4 5
- L only for b760m aorus elite ax ddr4 5
- 2 motherboard block diagram 6
- J only for b760m aorus elite ax k only for b760m aorus elite l only for b760m aorus elite ax ddr4 m only for b760m aorus elite ddr4 6
- 3 box contents 7
- 1 installation precautions 8
- Chapter 2 hardware installation 8
- 2 product specifications 9
- 2 productspecifications 9
- 3 installing the cpu and cpu cooler 12
- A note the cpu orientation 12
- B installing the cpu 13
- Do not force to engage the cpu socket locking lever when the cpu is not installed correctly as this would damage the cpu and cpu socket 13
- Follow the steps below to correctly install the cpu into the motherboard cpu socket 13
- Be sure to install the cpu cooler after installing the cpu actual installation process may differ depending the cpu cooler to be used refer to the user s manual for your cpu cooler 14
- C installing the cpu cooler 14
- 4 installing the memory 15
- Dualchannelmemoryconfiguration 15
- 5 installing an expansion card 16
- 6 back panel connectors 17
- Displayport 17
- Hdmi port 17
- Port with usb 3 gen 2x2 support 17
- Sma antenna connectors 2t2r jl 17
- Usb 2 1 port 17
- Usb 3 gen 1 port 17
- Usb 3 gen 2 type a port red q flash plus port 17
- Usb type 17
- Line out front speaker out 18
- Mic in rear speaker out 18
- Optical s pdif out connector 18
- Rj 45 lan port 18
- 7 onboard buttons and leds 19
- Qflash_plus q flash plus button 19
- Quick button 19
- 8 internal connectors 20
- 2 atx_12v_2x2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power 21
- Connector 21
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 21
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 21
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 21
- 4 cpu_fan sys_fan1 2 3 fan headers 22
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 22
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from 22
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip 22
- Connector cpu_fan sys_fan1 2 3 22
- D_led1 d_led2 addressable led strip headers 22
- Maximum current 2a 2a 22
- Maximum power 24w 24w 22
- No pin 22
- Overheating overheating may result in damage to the cpu or the system may hang 22
- Pin no definition 22
- Pwm speed control 22
- The headers can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds 22
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers 22
- Voltage speed control 22
- Before installing the devices be sure to turn off the devices and your computer unplug the power cord from the power outlet to prevent damage to the devices 23
- Chipset supports raid 0 raid 1 raid 5 and raid 10 please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array 23
- Connect your rgb led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 12v of this header incorrect connection may lead to the damage of the led strip 23
- For how to turn on off the lights of the led strip please navigate to the unique features page of gigabyte s website 23
- Led_c1 led_c2 rgb led strip headers 23
- Sata3 4 5 6 7 sata 6gb s connectors 23
- The headers can be used to connect a standard 5050 rgb led strip 12v g r b with maximum power rating of 2a 12v and maximum length of 2m 23
- The sata connectors conform to sata 6gb s standard and are compatible with sata 3gb s and sata 1 gb s standard each sata connector supports a single sata device the inte 23
- To enable hot plugging for the sata ports please navigate to the bios setup page of gigabyte s website and search for sata configuration for more information 23
- Install the m ssd https www gigabyte com webpage 920 m2 latchplus html remove the m ssd https www gigabyte com webpage 921 removem2 html 24
- M pcie x4 ssd m pcie x2 ssd m sata ssd 24
- M2a_cpu a a 24
- M2a_cpu follow the steps below to correctly install an m ssd in the m connector step 1 use a screwdriver to unfasten the screw on the heatsink step 2 insert the m ssd into the m connector at an angle press down on the front end of the m ssd remove the protective film from the bottom of the motherboard heatsink and then replace the heatsink and tighten the screws 24
- M2a_cpu m2p_sb m socket 3 connectors 24
- M2p_sb a a 24
- M2p_sb follow the steps below to correctly install an m ssd in the m connector step 1 locate the proper mounting hole for the m ssd to be installed and then install the m ez latch plus clip first step 2 insert the m ssd into the m connector at an angle press down on the front end of the m ssd and make sure the m ssd is secured by the m ez latch plus clip 24
- Please visit gigabyte s website for details on using m ez latch plus 24
- The m connectors on the motherboard support only m pcie ssds 24
- Types of m ssds supported by each m connector 24
- F_panel front panel header 25
- Cc1 18 d 26
- F_audio front panel audio header 26
- F_u32c usb type 26
- Gnd 14 gnd 26
- Head phone detection 26
- Head phone l 26
- Head phone r 26
- Header with usb 3 gen 2 support 26
- Mic detection 26
- No pin 26
- Pin no definition 26
- Pin no definition pin no definition 26
- Rx1 15 rx2 26
- Rx1 16 rx2 26
- Sbu1 19 d 26
- Sbu2 20 cc2 26
- Sense_send 26
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 26
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 26
- The header conforms to usb 3 gen 2 specification and can provide one usb port 26
- Tx1 12 tx2 26
- Tx1 13 tx2 26
- Vbus 11 vbus 26
- Vbus 17 gnd 26
- D1 18 ssrx2 27
- D1 19 vbus 27
- F_u32 usb 3 gen 1 header 27
- F_usb1 f_usb2 usb 2 1 headers 27
- Gnd 14 sstx2 27
- Gnd 17 ssrx2 27
- Nc 20 no pin 27
- No pin 27
- Pin no definition 27
- Pin no definition pin no definition 27
- Power 5v 27
- Prior to installing the usb bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the usb bracket 27
- Ssrx1 12 d2 27
- Ssrx1 13 gnd 27
- Sstx1 15 sstx2 27
- Sstx1 16 gnd 27
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer 27
- The headers conform to usb 2 1 specification each usb header can provide two usb ports via an optional usb bracket for purchasing the optional usb bracket please contact the local dealer 27
- Usb dx 27
- Usb dy 27
- Vbus 11 d2 27
- Add in card 28
- Add in card connectors 28
- Chip select 28
- Data input 28
- Data output 28
- No pin 28
- Pin no definition 28
- Power 3 v 28
- Spi_tpm trusted platform module header 28
- Supports a thunderbol 28
- Thb_c1 thb_c2 thunderbol 28
- The connectors are used to connect to a gigabyte thunderbol 28
- You may connect an spi tpm trusted platform module to this header 28
- Clr_cmos clear cmos jumper 29
- Rst reset jumper 29
- Bat battery 30
- Chapter 3 bios setup 31
- Function keys 32
- Startup screen 32
- 1 operating system installation 33
- Chapter 4 installing the operating system and drivers 33
- 2 drivers installation 34
- 1 configuring a raid set 35
- 1 configuringaraidset 35
- Before you begin please prepare the following items 35
- Chapter 5 appendix 35
- Raid levels 35
- Regulatory notices 36
- United states of america federal communications commission statement 36
- 2 應避免影響附近雷達系統之操作 38
- Corporation wireless module model name ax211ngw 38
- European community radio equipment directive compliance statement 38
- Japan wireless statement 5 5 ghz 帯 5 5 ghz 帯 屋内のみの使用 38
- Korea kcc ncc wireless statement 5 25ghz 5 35 ghz 대역을 사용하는 무선 장치는 실내에서만 사용하도록 제한됩니다 38
- Ncc wireless statements 無線設備警告聲明 低功率電波輻射性電機管理辦法 1 取得審驗證明之低功率射頻器材 非經核准 公司 商號或使用者均不得擅自變更頻率 加大功率或變更原設計之 特性及功能 低功率射頻器材之使用不得影響飛航安全及干擾合法通信 經發現有干擾現象時 應立即停用 並改 善至無干擾時方得繼續使用 前述合法通信 指依電信管理法規定作業之無線電通信 低功率射頻器材須忍受合法 通信或工業 科學及醫療用電波輻射性電機設備之干擾 38
- This equipment complies with all the requirements and other relevant provisions of radio equipment directive 2014 53 eu this equipment is suitable for home and office use in all the european community member states and efta member states the low band 5 5 5 5 ghz is for indoor use only 38
- Wireless module approvals 38
- Wireless module manufacturer inte 38
- Contact us 39
- Gigabyte esupport 39
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com 39
Похожие устройства
- Gigabyte B760M AORUS ELITE DDR4 Руководство пользователя по BIOS
- Gigabyte B760M AORUS ELITE DDR4 Инструкция по эксплуатации
- Gigabyte B760M AORUS ELITE AX DDR4 Руководство пользователя по BIOS
- Gigabyte B760M AORUS ELITE AX DDR4 Инструкция по эксплуатации
- Gigabyte B760M AORUS PRO Руководство пользователя по BIOS
- Gigabyte B760M AORUS PRO Инструкция по эксплуатации
- Gigabyte B760M AORUS PRO AX Руководство пользователя по BIOS
- Gigabyte B760M AORUS PRO AX Инструкция по эксплуатации
- Gigabyte B760M AORUS PRO DDR4 Руководство пользователя по BIOS
- Gigabyte B760M AORUS PRO DDR4 Инструкция по эксплуатации
- Gigabyte B760M AORUS PRO AX DDR4 Руководство пользователя по BIOS
- Gigabyte B760M AORUS PRO AX DDR4 Инструкция по эксплуатации
- Gigabyte B760M D2H Руководство пользователя по BIOS
- Gigabyte B760M D2H Инструкция по эксплуатации
- Gigabyte B760M D2H DDR4 Руководство пользователя по BIOS
- Gigabyte B760M D2H DDR4 Инструкция по эксплуатации
- Gigabyte B760M D3H DDR4 Руководство пользователя по BIOS
- Gigabyte B760M D3H DDR4 Инструкция по эксплуатации
- Gigabyte B760M DS3H Руководство пользователя по BIOS
- Gigabyte B760M DS3H Инструкция по эксплуатации