Makita DFJ206ZXL [9/72] Installation

Makita DFJ206ZXL [9/72] Installation
9 ENGLISH
PARTS DESCRIPTION
►Fig.1
1 Batteryholder(10.8V/
10.8 V - 12 V max)
(optional accessory)
2 Battery holder (14.4 V
/18V)
(optional accessory)
3 Loop for name badge 4 Loop for arm badge
5 Sleeve holder 6 Battery pocket 7 Mesh pocket for ice pack 8 Fan unit
9 Power cable 10 Anti-slip rubber
(DFJ207, DFJ305 and
DFJ407 only)
11 Hood
(DFJ207, DFJ305 and
DFJ407 only)
- -
INSTALLATION
Installing or removing the battery
cartridge
CAUTION: Always switch off the device
before installing or removing the battery
cartridge.
CAUTION: Hold the battery holder and the
battery cartridge rmly when installing or remov-
ing the battery cartridge. Failure to hold the battery
holderandthebatterycartridgermlymaycause
them to slip out of your hands and result in damage
tothebatteryholderandbatterycartridgeand/ora
personalinjury.
►Fig.2: 1. Red indicator 2. Button 3. Battery cartridge
4. Battery holder (optional accessory)
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert the battery cartridge all the way until
it locks in place with a small click. If you can see the red
indicator on the upper side of the button, it is not locked
completely.
To remove the battery cartridge, slide it from the battery
holder while pressing the button on the front of the
cartridge.
CAUTION: Always install the battery car-
tridge fully until the red indicator cannot be seen.
Otherwise the battery cartridge may accidentally
falloutofthebatteryholder,causinginjurytoyouor
someone around you.
CAUTION: Do not forcibly install the battery
cartridge. If the battery cartridge does not slide in
easily, it is not being inserted correctly.
Attaching the battery holder
You can hang the battery holder on your waist belt.
To prevent the battery holder from dropping acciden-
tally, attach a strap using the strap hole and secure it.
►Fig.3: 1. Strap hole
For 18V and 14.4V battery holders
The battery holder has an anti-drop function. When
removing the battery holder from the belt, pull up the
battery holder while pressing the unlock button.
►Fig.4: 1. Unlock button
Installing or removing the fan unit
1. Turn the ring counterclockwise while lifting the
hook on it. Remove the ring when the mark on the ring
aligns with the slot on the fan unit.
►Fig.5: 1. Fan unit 2. Ring 3. Hook 4. Slot 5. Mark
2. Pass the head of the fan unit into the hole on the
jacket.Settheringontothefanunitandturnitclock-
wise until the mark on the ring aligns with the mark
further from the slot.
►Fig.6: 1. Mark 2. Ring 3. Fan unit
3. Pass the strip through the loop on the fan unit and
fasten the snap button.
►Fig.7: 1. Strip
4.
Attachtheotherfanunittothejacketinthesameway.
5. Connect the cable to the fan units. Support the
cable using the cable holder.
►Fig.8: 1. Cable 2. Cable holder
6. Connect the other end of the cable to the battery
holder.
►Fig.9: 1. Battery holder
CAUTION:
Always use the strip and snap but-
ton to secure the fan unit to the jacket. If the fan unit
falls,itmaycauseaninjury,ordamagetothefanunit.
Follow the installation procedure in reverse when
removing it.
Attaching the lter set
Optional accessory
Theltersetprotectsthefanunitfromdustandpowder.
Werecommendthatyouusetheltersetinadustyor
powdery work place.
Insertthelterattachmentbetweenthejacketandfan
unitasshowninthegure.
►Fig.10: 1. Ring 2.Holeinthejacket3. Filter attach-
ment 4. Fan unit 5. Filter
When tightening the ring, stop it at the mark near the
slot on the fan unit. After attaching the fan units, cover
thelterattachmentswithlters.
►Fig.11: 1. Mark 2. Slot
NOTICE: Make sure that the lter fully covers
the lter attachment. For better protection against
dust and powder, tuck the skirt of the lter
between the jacket and lter attachment.

Содержание

Скачать