![Gigabyte Z690I AORUS ULTRA PLUS [25/40] Speaker speaker header](/img/pdf.png)
Gigabyte Z690I AORUS ULTRA PLUS [25/40] Speaker speaker header
![Gigabyte Z690I AORUS ULTRA PLUS [25/40] Speaker speaker header](/views2/1919625/page25/bg19.png)
- 25 -
11) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, and system status indicator on the chassis to this header according
to the pin assignments below. Note the positive and negative pins before connecting the cables.
System Status LED
S0 On
S3/S4/S5 Off
• PW (Power Switch):
Connects to the power switch on the chassis front panel. You may congure the way to turn off your
system using the power switch (please visit the "BIOS Setup," "Settings\Platform Power," webpage of
GIGABYTE's website for more information).
• HD (Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
• RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if
the computer freezes and fails to perform a normal restart.
• NC: No connection.
• PLED (Power LED):
Connects to the power status indicator on the chassis front panel. The LED is
on when the system is operating. The LED is off when the system is in S3/S4
sleep state or powered off (S5).
The front panel design may differ by chassis. A front panel module mainly consists of power
switch, reset switch, power LED, hard drive activity LED and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments
are matched correctly.
1 2
9 10
NC
PLED-
PW-
PLED+
PW+
HD-
RES+
HD+
RES-
Power Switch
Hard Drive
Activity LED
Reset Switch
Power LED
12) SPEAKER (Speaker Header)
The system reports system startup status by issuing a beep code. One single short beep will be heard if no
problem is detected at system startup. This header can also provide audio output in the operating system.
Pin No. Denition
1 SPK+
2 SPK-
1
Содержание
- Z690i a ultra plus 1
- Z690i a ultra plus d4 1
- Z690i aorus ultra plus 1
- Z690i aorus ultra plus ddr4 1
- Copyright 2
- Disclaimer 2
- Identifying your motherboard revision 2
- Chapter 1 product introduction 3
- Chapter 2 hardware installation 3
- Chapter 3 bios setup 0 3
- Chapter 4 installing the operating system and drivers 2 3
- Chapter 5 appendix 4 3
- Table of contents 3
- 1 motherboard layout 4
- Chapter 1 product introduction 4
- Note 1 the connector chip is on the back of the motherboard note 2 the connector is on the back of gc z690i btb plug 4
- Z690i aorus ultra plus 4
- Gc z690i btb plug 5
- Note 1 the connector chip is on the back of the motherboard note 2 the connector is on the back of gc z690i btb plug 5
- Z690i aorus ultra plus ddr4 5
- 2 motherboard block diagram 6
- Cpu clk 80 800 mhz 6
- J only for z690i aorus ultra plus 6
- K only for z690i aorus ultra plus ddr4 6
- Lga1700 cpu 6
- Pci express 3 bus 6
- Pci express 4 bus 6
- Pci express 5 bus 6
- Pci express x16 6
- 3 box contents 7
- 1 installation precautions 8
- Chapter 2 hardware installation 8
- 2 product specifications 9
- 2 productspecifications 9
- 3 installing the cpu and cpu cooler 12
- A note the cpu orientation 12
- B installing the cpu 13
- Do not force to engage the cpu socket locking lever when the cpu is not installed correctly as this would damage the cpu and cpu socket 13
- Follow the steps below to correctly install the cpu into the motherboard cpu socket 13
- Be sure to install the cpu cooler after installing the cpu actual installation process may differ depending the cpu cooler to be used refer to the user s manual for your cpu cooler 14
- C installing the cpu cooler 14
- 4 installing the memory 15
- Dualchannelmemoryconfiguration 15
- 5 installing an expansion card 16
- 6 back panel connectors 17
- Displaypor 17
- Hdmi 2 port 17
- Rj 45 lan port 17
- Usb 2 1 port 17
- Usb 3 gen 1 port 17
- Usb 3 gen 2 type a port q flash plus port 17
- Usb type 17
- Line out 18
- Mic in 18
- Q flash plus butto 18
- Sma antenna connectors 2t2r 18
- Usb 3 gen 2 type a port red 18
- 7 internal connectors 19
- 12v 22 5v 20
- 12v only for 2x12 pin atx 20
- 12v only for 2x4 pin 12v 20
- 2 atx_12v_2x4 atx 2x4 12v power connector and 2x12 main power connector 20
- 3 v 13 3 v 20
- 3 v 14 12v 20
- 3 v only for 2x12 pin atx 20
- 5v 16 ps_on soft on off 20
- 5v 18 gnd 20
- 5v only for 2x12 pin atx 20
- 5vsb stand by 5v 21 5v 20
- Gnd 15 gnd 20
- Gnd 17 gnd 20
- Gnd 19 gnd 20
- Gnd only for 2x12 pin atx 20
- Gnd only for 2x4 pin 12v 20
- Pin no definition 20
- Pin no definition pin no definition 20
- Power good 20 nc 20
- The 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the 12v power connector mainly supplies power to the cpu if the 12v power connector is not connected the computer will not start 20
- To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500w or greater if a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system 20
- With the use of the power connector the power supply can supply enough stable power to all the components on the motherboard before connecting the power connector first make sure the power supply is turned off and all devices are properly installed the power connector possesses a foolproof design connect the power supply cable to the power connector in the correct orientation 20
- 5 cpu_fan sys_fan1 sys_fan 21
- All fan headers on this motherboard are 4 pin most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design for optimum heat dissipation it is recommended that a system fan be installed inside the chassis 21
- Connect one end of the ext_pwr cable to this connector and the other end to your power supply 21
- Ext_pw 21
- External power connector 21
- Fan headers 21
- Note the connector is on the front of gc z690i btb plug 21
- Pin no definition 21
- Pwm speed control 21
- Voltage speed control 21
- Addressable led strip header 22
- Be sure to connect fan cables to the fan headers to prevent your cpu and system from 22
- Connect your addressable led strip to the header the power pin marked with a triangle on the plug of the led strip must be connected to pin 1 of the addressable led strip header incorrect connection may lead to the damage of the led strip 22
- Connector cpu_fan sys_fan1 sys_fan2 cpu_opt 22
- Cpu_opt water cooling cpu fan header 22
- Maximum current 2a 2a 2a 2a 22
- Maximum power 24w 24w 24w 24w 22
- No pin 22
- Note the connector is on the front of gc z690i btb plug 22
- Overheating overheating may result in damage to the cpu or the system may hang 22
- Pin no definition 22
- Pwm speed control 22
- The fan header is 4 pin and possesses a foolproof insertion design most fan headers possess a foolproof insertion design when connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire the speed control function requires the use of a fan with fan speed control design 22
- The header can be used to connect a standard 5050 addressable led strip with maximum power rating of 5a 5v and maximum number of 1000 leds 22
- These fan headers are not configuration jumper blocks do not place a jumper cap on the headers 22
- Voltage speed control 22
- Led_c rgb led strip header 23
- Sata3 0 1 j sata3 0 1 2 3 k sata 6gb s connectors 23
- Follow the steps below to correctly install an m ssd in the m connector on gc z690i btb plug step 1 use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink 24
- Gc z690i btb plug 24
- Heatsink 24
- M pcie x4 ssd m pcie x2 ssd m sata ssd 24
- M socket 3 connectors 24
- M2a_cp 24
- M2a_cpu 24
- M2a_cpu a a 24
- M2p_sb 24
- M2p_sb a a 24
- Note 1 the connector is on the back of gc z690i btb plug note 2 the connector is on the front of gc z690i btb plug 24
- Step 2 m2a_cpu u to use the m2a_cpu connector you have to remove gc z690i btb plug from the motherboard first use a screwdriver to remove the screw from gc z690i btb plug lift gc z690i btb plug upwards and remove it 24
- Step 3 locate the proper mounting hole based on the length of your m ssd drive if needed move the standoff to the desired mounting hole insert the m ssd into the m connector at an angle press the m ssd down and then use the included screw to secure it in the connector 24
- Step 4 m2a_cpu insert gc z690i btb plug vertically into the btb connectors and secure it with the screw then screw the heatsink back on m2p_sb screw the heatsink back on 24
- There are two types of m ssds m sata ssds and m pcie ssds this motherboard only supports m pcie ssds be sure to verify the type of m ssds you want to use please note that an m pcie ssd cannot be used to create a raid set with a sata hard drive please navigate to the configuring a raid set page of gigabyte s website for instructions on configuring a raid array 24
- Types of m ssds supported by each m connector 24
- V remove protective film c m2p_sb remove protective films a and b 24
- F_panel front panel header 25
- Speaker speaker header 25
- Cc1 18 d 26
- D1 18 ssrx2 26
- D1 19 vbus 26
- F_u32 usb 3 gen 1 header 26
- F_u32c usb type 26
- Gnd 14 gnd 26
- Gnd 14 sstx2 26
- Gnd 17 ssrx2 26
- Header with usb 3 gen 2 support 26
- Nc 20 no pin 26
- Pin no definition pin no definition 26
- Rx1 15 rx2 26
- Rx1 16 rx2 26
- Sbu1 19 d 26
- Sbu2 20 cc2 26
- Ssrx1 12 d2 26
- Ssrx1 13 gnd 26
- Sstx1 15 sstx2 26
- Sstx1 16 gnd 26
- The header conforms to usb 3 gen 1 and usb 2 specification and can provide two usb ports for purchasing the optional 3 front panel that provides two usb 3 gen 1 ports please contact the local dealer 26
- The header conforms to usb 3 gen 2 specification and can provide one usb port 26
- Tx1 12 tx2 26
- Tx1 13 tx2 26
- Vbus 11 d2 26
- Vbus 11 vbus 26
- Vbus 17 gnd 26
- Clr_cmos clear cmos jumper 27
- Usb 2 1 header 27
- Always turn off your computer and unplug the power cord before replacing the battery replace the battery with an equivalent one damage to your devices may occur if the battery is 28
- Bat battery 28
- Battery 28
- Contact the place of purchase or local dealer if you are not able to replace the battery by yourself 28
- Header and wait for one minute 28
- Note the connector is on the front of gc z690i btb plug 28
- Or uncertain about the battery model 28
- Pin no definition 28
- Plug in the battery cable 4 plug in the power cord and restart your computer 28
- Replaced with an incorrect model 28
- Rst reset button reset jumper 28
- Rst_sw 28
- Rst_sw rst 28
- Rtc power 28
- The battery provides power to keep the values such as bios configurations date and time information in the cmos when the computer is turned off replace the battery when the battery voltage drops to a low level or the cmos values may not be accurate or may be lost 28
- The reset button rst_sw allows users to quickly turn on off the computer in an open case environment when they want to change hardware components or conduct hardware testing the reset jumper rst can connect to the reset switch on the chassis front panel press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart 28
- The reset button rst_sw rest jumper rst provides you with several functions to use to remap the button to perform different tasks please navigate to the bios setup page of gigabyte s website and search for rst_sw multikey for more information 28
- Turn off your computer and unplug the power cord 2 unplug the the battery cable from the battery cable 28
- Used batteries must be handled in accordance with local environmental regulations 28
- You may clear the cmos values by removing the 28
- Default location of the f_audio header heatsink 29
- F_audio front panel audio header 29
- Gc z690i btb plug 29
- Gnd 7 sense_send 29
- Head phone r 10 head phone detection 29
- Mic l 6 mic detection 29
- Mic r 8 no pin 29
- Nc 9 head phone l 29
- Pin no definition pin no definition 29
- Please visit gigabyte s website for details on using the front panel audio header 29
- Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug for information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 29
- Step 1 use a screwdriver to unfasten the screw on the heatsink and then remove the heatsink 29
- Step 2 use a screwdriver to remove the screw from gc z690i btb plug lift the gc z690i btb plug upwards and remove it 29
- Step 3 move the f_audio header out of its default location and route it via the btb connector to the bottom edge of the motherboard as shown on the left 29
- Step 4 insert gc z690i btb plug vertically into the btb connectors and secure it with the screw then screw the heatsink back on 29
- Suggested f_audio header routing 29
- The front panel audio header supports high definition audio hd you may connect your chassis front panel audio module to this header make sure the wire assignments of the module connector match the pin assignments of the motherboard header incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it 29
- Chapter 3 bios setup 30
- Function keys 31
- Startup screen 31
- 1 operating system installation 32
- Chapter 4 installing the operating system and drivers 32
- 2 drivers installation 33
- 1 configuring a raid set 34
- 1 configuringaraidset 34
- Before you begin please prepare the following items 34
- Chapter 5 appendix 34
- Raid levels 34
- Regulatory notices 35
- United states of america federal communications commission statement 35
- 2 應避免影響附近雷達系統之操作 37
- 5 5ghz 屋内限定 5 5 5 5ghz indoor use only except communicate to high power radio 37
- At be bg ch cy cz de 37
- Ccah22y10140t1 37
- Complies with imda standards da108442 37
- Corporation wireless module model name ax411ngw 37
- Dk ee el es fi fr hr 37
- European community radio equipment directive compliance statement 37
- Hu ie is it li lt lu 37
- Japan wireless statement 5 5 ghz 帯 5 5 ghz 帯 屋内のみの使用 37
- Korea kcc ncc wireless statement 5 25ghz 5 35 ghz 대역을 사용하는 무선 장치는 실내에서만 사용하도록 제한됩니다 37
- Lv mt nl pl pt ro se 37
- Ncc wireless statements 無線設備警告聲明 低功率電波輻射性電機管理辦法 1 取得審驗證明之低功率射頻器材 非經核准 公司 商號或使用者均不得擅自變更頻率 加大功率或變更原設計之特 性及功能 低功率射頻器材之使用不得影響飛航安全及干擾合法通信 經發現有干擾現象時 應立即停用 並改善至 無干擾時方得繼續使用 前述合法通信 指依電信管理法規定作業之無線電通信 低功率射頻器材須忍受合法通信或 工業 科學及醫療用電波輻射性電機設備之干擾 37
- Si sk tr uk 37
- This equipment complies with all the requirements and other relevant provisions of radio equipment directive 2014 53 eu this equipment is suitable for home and office use in all the european community member states and efta member states the low band 5 5 5 5 ghz is for indoor use only 37
- Ua tr 28 37
- Wireless module approvals wireless module manufacturer inte 37
- И011 21 37
- 総務 37
- Contact us 40
- Gigabyte esupport 40
- To submit a technical or non technical sales marketing question please link to https esupport gigabyte com 40
Похожие устройства
- Gigabyte Z690I AORUS ULTRA PLUS DDR4 Руководство пользователя по BIOS
- Gigabyte Z690I AORUS ULTRA PLUS DDR4 Инструкция по эксплуатации
- Gigabyte Z690M AORUS ELITE DDR4 Руководство пользователя по BIOS
- Gigabyte Z690M AORUS ELITE DDR4 Инструкция по эксплуатации
- Gigabyte Z690M AORUS ELITE AX DDR4 Руководство пользователя по BIOS
- Gigabyte Z690M AORUS ELITE AX DDR4 Инструкция по эксплуатации
- Gigabyte Z690M DS3H DDR4 Руководство пользователя по BIOS
- Gigabyte Z690M DS3H DDR4 Инструкция по эксплуатации
- Gigabyte B660 AORUS ELITE AX DDR4 Руководство пользователя по BIOS
- Gigabyte B660 AORUS ELITE AX DDR4 Инструкция по эксплуатации
- Gigabyte B660 AORUS ELITE DDR4 Руководство пользователя по BIOS
- Gigabyte B660 AORUS ELITE DDR4 Инструкция по эксплуатации
- Gigabyte B660 AORUS MASTER Руководство пользователя по BIOS
- Gigabyte B660 AORUS MASTER Инструкция по эксплуатации
- Gigabyte B660 AORUS MASTER DDR4 Руководство пользователя по BIOS
- Gigabyte B660 AORUS MASTER DDR4 Инструкция по эксплуатации
- Gigabyte B660 DS3H AC Руководство пользователя по BIOS
- Gigabyte B660 DS3H AC Инструкция по эксплуатации
- Gigabyte B660 DS3H AC DDR4 Руководство пользователя по BIOS
- Gigabyte B660 DS3H AC DDR4 Инструкция по эксплуатации