Главная
Skipped breadcrumb items
JS550
Инструкция Страница: 4

Главная
STATUS
JS550
Инструкция Страница: 4

STATUS JS550 — основные правила безопасной эксплуатации электроинструментов [4/29]

Превью страниц Страница 4 / 29

6 7

3. OPERATION 3. OPERATION

and pull the mains plug when the cable is damaged while operating. Damaged

cables increase the risk of electric shock.• Keep work area clean. Blends of

materials are particularly dangerous. Dust from light alloys can burn or explode.

• Always wait until the machine has come to a complete stop before placing it down.

• The tool must be used only for its prescribed purpose. Any use other than those

mentioned in this Manual will be considered a case of misuse. The user and not

the manufacturer shall be liable for any damage or injury resulting from such cases

of misuse.

• To use this tool properly, you must observe the safety regulations, the assembly

instructions and the operating instructions found in this Manual. All persons who

use and service the machine have to be acquainted with this Manual and must be

informed about its potential hazards. Children and frail people must not use this

tool. Children should be supervised at all times if they are in the area in which the

tool is being used. It is also imperative that you observe the accident prevention

regulations in force in your area.

The same applies for general rules of occupational health and safety.

• The manufacturer shall not be liable for any changes made to the tool nor for any

damage resulting from such changes.

• Power tools must not be used outdoors in rainy weather, or in moist environment

(after rain) or in close vicinity with easily flammable liquids and gases. The working

place should be well lit.

OPERATION

KNOW YOUR PRODUCT

Before using the power tool, familiarize yourself with all the operating features and

safety requirements. Use the tool and accessories only for the applications intended.

All other applications are expressly ruled out.

1. ON/OFF switch

2. Variable speed regulator

3. Lock-on button

4. Fence

5. Base plate

6. Bevel angle scale

7. Saw blade

8. Pendulum stroke knob

9. Dust extraction adapter

This power tool is designed for sawing wooden, plastic and metal plates and

shapes.

PRIOR TO INITIAL OPERATION

• Make sure the power supply voltage corresponds to the value indicated on the

name plate with technical data of the tool.

• Always check the position of ON/OFF switch. The power tool must be connected

to the power supply socket only when this switch is in OFF position. If the plug is

connected to a receptacle while the power switch is in the ON position, the power

tool will start operating immediately, which could cause a serious accident.

• Make sure that the cord and the plug are in order. If the replacement of the supply

cord is necessary, this has to be done by the manufacturer or his agent in order

to avoid a safety hazard.

• Always make sure that the blade is secured in the holder.

WARNING: Always switch off and unplug the power tool prior to any

adjustment, servicing or maintenance or in case of mains drop-out.

SWITCHING ON - SWITCHING OFF

Brief activation:

Switching on: press ON/OFF switch (1).

Switching off: release ON/OFF switch (1).

Continuous use:

Switching on: press ON/OFF switch (1) and in pressed position lock it by button (3).

Switching off: press ON/OFF switch (1) once and release it immediately.

In case of mains drop-out during operation while the lock-on button (3) is engaged,

release the lock-on button immediately.

Do not lock the ON/OFF switch by button (3) while performing jobs which may

require instant stopping of the saw.

ADJUSTING THE SPEED

Speed adjusting dial

The tool speed can be infinitely adjusted between 800 and 3,000 strokes per

minute by turning the adjusting dial.

Higher speed is obtained when the dial is turned in the direction of number 6.

Lower speed is obtained when it is turned in the direction of number 1.

Refer to the table to select the proper speed for the workpiece to be cut.

However, the appropriate speed may differ with the type or thickness of the

workpiece. In general, higher speeds will allow you to cut workpieces faster but the

service life of the blade will be reduced.

The stroke rate must suit the kind of processed material.

The following guidelines may be used in determining correct speed for various

applications:

• LOW speed is appropriate for starting cuts.

• MEDIUM speed is suitable for cutting hard metal, plastics and laminates.

• HIGH speed produces best results when cutting wood, aluminium, brass and

copper.

Define the optimum speed by making a test cut in a piece of waste material.

10. Roller guide

11. Parallel guide

12. Parallel guide ﬁxing screw

13. Blade guard

14. Hex key

15. Blade quick release button

STATUS JS550 — основные правила безопасной эксплуатации электроинструментов [4/29]

Содержание

Похожие устройства