Vitek VT-8325 [4/32] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Vitek VT-8325 [4/32] English

Vitek VT-8325 [4/32] English
4
ENGLISH
• The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision of
a person who is responsible for their safety or
if they are not instructed by this person on the
usage of the unit.
• Do not use the unit if the power cord or the
plug is damaged, if the unit works improperly
or after it was dropped or in case of leakage.
• If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
• Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
• Transport the unit in the original package only.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on.
• Unpack the iron; remove the protection from
the soleplate (13), if any.
• Check the unit for damages, do not use the
iron in case of damages.
• Before switching the iron on, make sure that
your home mains voltage corresponds to the
iron operating voltage.
• The unit is intended for operation from an AC
power network with the frequency of 50 or
60 Hz. The unit does not need any additional
settings for operating with the required rated
frequency.
• There may be water residue in the tank, this
is normal, as the iron has undergone factory
quality control.
Note: While the first switching on the heating
element of the iron burns, therefore occurrence
of foreign smell and a small amount of smoke is
possible, it is normal.
Control knobs, indications
and symbols
• The continuous steam supply knob (3) has
3 fixed positions:
– – steam supply is off;
– – steam supply is on;
– – «double steam»
and one unfixed position:
– – self-clean.
• Burst of steam button (4) – press the button to
activate the additional steam supply function.
• Water spray button (5) – press the button to
activate the water spray function.
• Heating element ON/OFF indicator (7) – when
the indicator lights up, the iron soleplate is
heating up.
• Temperature control knob (11) – allows to
set the iron soleplate temperature depend-
ing on the type of fabric (see the table below).
The knob is in the position «MIN» – the iron
is off.
• «MAX» maximal water level mark
• The symbol indicates hot surfaces.
WATER SELECTION
You can use tap water to fill the water tank (10).
If tap water is hard, use distilled or deminer-
alized water, this will prolong service life of
the iron.
Note: Do not fill the water tank (10) with scented
liquids, vinegar, starch solution, descaling
reagents, chemical agents etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that
it is unplugged.
• Set the temperature control knob (11) to the
position «MIN», and the continuous steam
supply knob (3) to the position
– continu-
ous steam supply is off.
• Open the water inlet lid (2).
• Open the lid (2) and pour water into the water
tank (10) using the beaker (14) and then close
the lid (2) tight.
Note:
• Do not exceed the «MAX» mark (12).
• If you need to refill water during ironing,
always switch the iron off first and unplug it.
• After you finish ironing, switch the iron off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
IM VT-8325.indd 4 01.02.2019 9:51:42

Содержание

Похожие устройства

Скачать