Centek CT-0028 White [14/20] On the use of the appliance by the persons responsible for their safety take

Centek CT-0028 White [14/20] On the use of the appliance by the persons responsible for their safety take
14
- Do not touch the appliance with wet hands. In case of ingress of moisture or
leakage from the appliance immediately disconnect it from power supply.
- Always disconnect the appliance from power supply after use and before cleaning
(pull the plug, do not pull it out by the cable).
- Do not let children play with the appliance. Do not leave the appliance
unattended. Ensure that the power cable is routed in a location inaccessible
for children.
- Regularly check the appliance and its power cable for damage. Operating a
damaged appliance is not allowed.
- Do not attempt to repair the appliance yourselves, apply to certified technicians.
In case of damage to the power cable have it replaced by the Manufacturer, an
authorized service centre or other skilled personnel.
- Only the use of original spare parts is allowed.
- Special instructions for transportation (shipment) and sale: none.
SPECIAL SAFETY REQUIREMENTS
- Fill the kettle with cold water only.
- Ensure that the kettle is turned off before removing it from the base!
- Ensure that the lid is firmly closed before turning the kettle on.
- Do not attempt to boil water in the kettle with the lid open, this will prevent the
automatic shutdown from functioning and may cause a fire.
- Use the kettle only together with the base supplied with it.
- Avoid contact of water with the surface of the kettle and the power base.
- The water level should be between the MAX and MIN marks! If the kettle is folled
over the maximum level mark, boiling water may spill out!
- Use the appliance only with the proper connector.
- The appliance is not designed to be powered from an external timer or other
separate remote control system.
- CAREFUL: accessible surfaces of the appliance can reach high temperature
during operation. Do not touch the hot surfaces.
-
The appliance should not be used by physically, sensory or mentally handicapped
persons (including children) or by persons without sufficient experience or
knowledge, unless such persons are under supervision, or have been instructed
on the use of the appliance, by the persons responsible for their safety. Take
precautions not to children play with the appliance.
2. APPLIANCE DESCRIPTION
1. Cover
2. Non-heating housing
3. LED indicator
4. Power button
5. Handle
6. Power base with cord compartment
3. SCOPE OF SUPPLY
- Electric kettle – 1 pc.
- Kettle base – 1 pc.
- Operating Manual – 1 pc.
4. OPERATING PROCEDURE
Retain all packaging materials until you make sure that the kettle operates
properly.
Ensure that the power supply grid voltage corresponds to the one indicated on
the kettle’s base before operating it.
Do not operate the unit with damaged power cable or plug.
Before the first use boil and discard water two times. It is recommended to
add some citric acid to the water for the first boiling. The kettle is designed for
boiling pure water only.
Place the kettle on a smooth level surface. Do not place the kettle at the edge
of a table.
Connect the kettle to an electric socket. Excessive power cord can be wrapped
around the guides inside the base and draw its end through the cutout in its side.
Do not let the power cord hang from a table where a child can pull on it.
Do not place the kettle near heating appliances and hot surfaces.
KETTLE OPERATION
Before connecting the kettle to power supply ensure that the main power switch
is in the OFF position.
Hold the kettle by the handle and lift it vertically from the base. Open the lid.
Do not pour hot tap water into the kettle. Open the tap and let the water flow
for some time to make sure it is clean.
Pour water into the kettle. Check the water level by the level gage in the housing.
Do not overfill the kettle above the MAX mark. Be careful: if overfilled hot water
may be spilled put from the spout.
Close the lid until a click is heard. The kettle may not turn on if the lid is not
firmly closed.
Connect the kettle to power supply. Set the power switch to the ON position. The
LED indicator will go on. The kettle will turn off automatically when the water
boils. The indicator will go out.
Before dispensing water from the kettle wait for it to stop bubbling. For a repeated
boiling set the switch to the ON position. The power switch will not be retained
in the ON position for several seconds after boiling. Do not manually retain the
switch in the ON position! The heating may be stopped at any time by pressing
the ON/OFF button.
Take the kettle from the base vertically, holding it by the handle. Some
condensation may be visible on the top side of the base after the kettle is
removed. This is normal and not a sign of malfunction.
ATTENTION! Do not turn the kettle on the base to avoid spilling out of hot water!
Ensure that the kettle is turned off before removing it from the base! Do not open
the lid during boiling!

Содержание

Скачать