Home
Главная
Skil
Граверы
1415 LC
Инструкция по эксплуатации Страница: 10

Skil 1415 LC Инструкция по эксплуатации онлайн [10/188] 92684

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Use only accessories recommended by SKIL

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• Do not use damaged, deformed or vibrating accessories

• Handle and store grinding/cutting discs carefully to avoid

chipping and cracking

• Protect accessories from impact, shock and grease

• Never use grinding discs over 32 mm (1 1/4”) Ø

• Never use drill bits over 3.2 mm (1/8”) Ø

• Never use a cutting disc for side grinding

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Wear protective glasses and hearing protection 4,

protective gloves and sturdy shoes; when necessary, also

wear an apron

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Ensure that the collet size corresponds with the shaft size

of the accessory

• Be sure tool is switched o when plugging in

DURING USE

• Use auxiliary handle(s), if supplied with the tool

(loss of control can cause personal injury)

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord (a cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock)

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Never use spindle lock while tool is running (damage

due to improper handling will be excluded from the

guarantee)

• Keep hands away from rotating accessories

• When grinding metal, sparks are generated; keep other

persons and combustible material from work area

• Keep the ventilation slots uncovered while working

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTER USE

• The accessory continues to rotate for a short time after

the tool has been switched o

• Before you put down the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• After switching o the tool, never stop the rotation of the

accessory by a force applied against it

• Store tool in locations where temperature will not exceed

50°C

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Changing accessories 5

! switch off the tool and disconnect the plug

! ensure that collet size corresponds with shaft

size of accessory

- push spindle-lock button B and hold it while you turn

collet nut D by hand until the spindle lock prevents

further rotation and loosen collet nut D with wrench E

- insert an accessory in collet C as far as possible to

minimize run-out and unbalance

- push spindle-lock button B and hold it while you

tighten collet nut D with wrench E

! avoid excessive tightening of collet nut D

! never tighten collet nut, if there is no accessory

in collet; collet may be damaged

• Changing collets 6

! switch off the tool and disconnect the plug

- push spindle-lock button B and hold it while you

remove collet nut D

- remove collet C

- insert new collet

! never tighten collet nut, if there is no accessory

in collet; collet may be damaged

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o switch 7

- switch on/o the tool by pushing knob A in “I”/”O”

position

! before the accessory reaches the workpiece, the

tool should run at full speed

Содержание

Похожие устройства

Always disconnect plug from power source before making any adjustment or changing any accessory ACCESSORIES SKIL can assure flawless functioning of the tool only when original accessories are used Use only accessories recommended by SKIL For mounting using non SKIL accessories observe the instructions of the manufacturer concerned Use only accessories with an allowable speed matching at least the highest no load speed of the tool Do not use damaged deformed or vibrating accessories Handle and store grinding cutting discs carefully to avoid chipping and cracking Protect accessories from impact sh ock and grease Never use grinding discs over 32 mm 1 1 4 0 Never use drill bits over 3 2 mm 1 8 0 Never use a cutting disc for side grinding Never use reducors or adaptors to fit large hole grinding cutting discs BEFORE USE Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool tools with a rating of 230V or 240V can also be connected to a 220V supply Do not work materials containing asbestos asbestos is considered carcinogenic Secure the workpiece a workpiece clamped with clamping devi ces or i n a vice i s hel d more securely than by hand Use completely unrolled and safe extension cords with a capacity of 16 Amps U K 13 Amps Wear protective glasses and hearing protection protective gloves and sturdy shoes when necessary also wear an apron Dust from material such as paint containing lead some wood species minerals and metal may be harmful contact with or inhalation of the dust may cause allergic reactions and or respiratory diseases to the operator or bystanders wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning wear a dust mask and work with a dust extraction device when connectable Follow the dust related national requirements for the materials you want to work with Ensure that the collet size corresponds with the shaft size of the accessory Be sure tool is switched off when plugging in DURING USE Use auxiliary handle s If supplied with the tool loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord a cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Always keep the cord away from moving parts of the tool direct the cord to the rear away from the tool Never use the tool when cord is damaged have it replaced by a qualified person Never use spindle lock while tool Is running damage due to improper handling will be excluded from the guarantee Keep hands away from rotating accessories When grinding metal sparks are generated keep other persons and combustible material from work area Keep the ventilation slots uncovered while working In case of electrical or mechanical malfunction immediately switch off the tool and disconnect the plug AFTER USE The accessory continues to rotate for a short time after the tool has been switched off Before you put down the tool switch off the motor and ensure that all moving parts have come to a complete standstill After switching off the tool never stop the rotation of the accessory by a force applied against it Store tool in locations where temperature will not exceed 50 C WHEN CONNECTING NEW 3 PIN PLUG U K ONLY Do not connect the blue neutral or brown live wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool it must be disposed of safely and not left unattended USE Changing accessories switch off the tool and disconnect the plug 1 ensure that collet size corresponds with shaft size of accessory push spindle lock button B and hold it while you turn collet nut D by hand until the spindle lock prevents further rotation and loosen collet nut D with wrench E insertan accessory in colletC as far as possible to minimize run out and unbalance push spindle lock button B and hold it while you ti ghten collet nut D wi th wren ch E I avoid excessive tightening of collet nut D I never tighten collet nut If there is no accessory In collet collet may be damaged Changing collets switch off the tool and disconnect the plug push spindle lock button B and hold it while you remove collet nut D removecolletC insert new collet I never tighten collet nut If there is no accessory In collet collet may be damaged Before using the tool ensure that accessory is correctly mounted and firmly tightened check if accessory runs freely by turning it by hand test run tool for at least 30 seconds at highest no load speed in a safe position stop immediately in case of considerable vibration or other defects and check tool to determine the cause On off switch switch on off the tool by pushing knob A in T O position before the accessory reaches the workpiece the tool should run at full speed 10

Скачать

Случайные обсуждения

Ответы 1

Какая смазка применяется при обслуживании Skil1415LC

1 год назад

Ответы 0

как открыть фонарь

1 год назад

Ответы 3

Подскажите диаметр посадочного места цанги.

3 года назад

Ответы 0

Требуется ли смазка машинки?

2 года назад