Maxwell MW-3818 BK [12/44] English

Maxwell MW-3818 BK [12/44] English
12
ENGLISH
• To avoid damaging the coating of the bowl
(12), do not put the bowl (12) under cold
water right after cooking; let the bowl cool
down preliminarily.
• The bowl (12) is not suitable for washing in
the dishwashing machine.
BASIC FUNCTIONS
DELAYED START FUNCTION
The delayed start function allows to set the
cooking end time. Do not use the delayed start
function to cook perishable products. Set the
delayed start time with the «DELAYED START»
button (17).
Example:
If the run-time of the selected cooking pro-
gram is 30 minutes, and the dish must be
ready in 2 hours, the unit will stay in the
stand-by mode for 1.5 hours and then the
set cooking program will be switched on.
1. After selecting the cooking program, press
the «DELAYED START» button (17), the
default delayed start time will be shown on
the display and the button (17) indicator will
be flashing.
2. Set the delayed start time (up to 24 hours) by
pressing the «DELAYED START» button (17)
consequently.
3. In 10 seconds the unit will be switched to the
delayed start mode, the selected program
indicator and the «DELAYED START» button
(17) indicator will light constantly.
4. When the unit is switched to the cooking
mode, the «DELAYED START» button (17)
indicator will go out.
KEEP WARM FUNCTION
After the cooking program ends, the unit will be
switched to the keep warm mode automatically.
The «MAINTAIN t°» button (16) indicator will be
glowing and the operation time in the keep warm
mode will be shown on the display (3).
Notes:
Despite the unit keeps the ready dish warm
for 24 hours, it is not recommended to leave
the cooked food in the bowl (12) for a long
time, because the food may spoil.
Do not use the keep warm mode to heat up
cold products.
Switch the keep warm function off imme-
diately after the «Baking» program is fin-
ished, otherwise the baked products may
burn.
MEMORY FUNCTION
In case of emergency power cutoff during the
multicooker operation the memory function
with the duration of up to 2 hours is activated.
If the power supply is restored within 2 hours,
the multicooker will continue to perform the
pre-set program from the moment it was
stopped at.
If there is no power for more than 2 hours, it is
necessary to reprogram the unit.
BEFORE THE FIRST USE
After unit transportation or storage under
cold (winter) conditions, it is necessary to
keep it for at least two hours at room tem-
perature before switching on.
1. Unpack the unit, remove any stickers and
package materials that can prevent multi-
cooker operation.
2. Make sure that the operating voltage of
the unit corresponds to the voltage of your
mains.
3. Place the multicooker on a flat, heat-resistant
surface away from all heat sources (such as a
gas cooker, electric cooker or cooking unit).
The gap between the multicooker body and
the wall should be at least 20 cm and the gap
above the unit should be at least 30-40 cm.
4. Do not place the multicooker close to the
objects that can be damaged by the released
steam of high temperature.
Attention! Do not place the unit near bath
tubs, kitchen sinks or other containers filled
with water.
5. Open the lid (4) by pressing the button (5)
and pulling the handle (6) upwards. Remove
the bowl (12) and remove the steam valve (7)
by pressing it from the inner side of the lid (4).
6. Wash all removable parts in warm water with
a neutral detergent: the bowl (12), the steam
valve (7), the steam cooking basket (19), the
spatula (20) and the measuring cup (21).
Rinse all the parts under running water and
dry them thoroughly.
7. Clean the unit body (1) with a damp cloth,
then wipe it dry.
8. Install the steam valve (7) into the lid (4).
PRODUCT LOADING
Make sure that the total amount of prod-
ucts and liquids doesn’t exceed the maxi-
mal mark «1and is not lower than the
minimal mark «4» (measuring scale in the
MW-3818.indd 12 21.03.2014 16:50:06
Скачать
Случайные обсуждения

Ответы 0

Электросхема мультиварки.
3 года назад