TRAYNOR K1CE [7/18] Basic setup
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

TRAYNOR K1CE [7/18] Basic setup

TRAYNOR K1CE [7/18] Basic setup
5
Basic Setup
1. Connect your K1’s power cord to the AC outlet making sure that the Power switch is off.
2. Connect your stereo keyboard to Channel 1 L/Mono and Right Inputs. If your instrument
only has a mono output, connect it to the L/Mono Input. In either case, balanced or
unbalanced cables may be used.
3. Connect your secondary (mono) instrument or other signal source to Channel 2’s ¼-
inch Mono Input (balanced or unbalanced cable may be used). You may connect your
microphone to the XLR Mic input. If the instrument does not use a pre-amp, the mic may
be slightly louder.
4. If you wish to be mixed down with the PA or recording console, connect a mono line
output on the mixer – e.g., Aux or monitor - to the K1’s Channel 3 Mon(itor) Input
(balanced or unbalanced cables may be used). Once again, it is strictly for your onstage
mix and will only be sent to the K1’s amp/speaker system, not the Balanced Line Out,
the Stereo Phones jack or the Link Out jacks. This is to avoid the risk of a gain loop being
created between the K1 and the mixer.
5. Connect your MP3, CD or tape player to the Aux Inputs.
6. Turn the Master and Channel 3 Gain to a low setting for now and switch on the Power.
7. Adjust the Channel 1 and 2 Gains along with the Bass/Treble EQ as desired during a
sound check.
8. Bring up the Master and Channel 3 Gain gradually to the desired volume level. The
Channel 2 EQ can be used to help control microphone feedback. Simply turn down Treble
if it’s high-frequency feedback, or turn down the Bass if it’s low-frequency feedback.
9. To Link a second K1, connect the Link Out jack to the other K1’s Link jack In with a stereo
or balanced ¼-inch TRS - to - ¼-inch TRS cable. Once again, additional instruments or
other sources may be connected to a second K1 and will come out both amps. Also a
reminder that the Link Out will only work if connected to one other K1’s Link In jack.
10. To feed the overall mix (without channel 3) to a PA mixer, run a TRS-TRS cable from the
K1’s Bal Line Out jack to a line-level input on the mixer.
Note: this is a pre-Master output so only the mixer will have level control over this signal for
the PA mix. That way the K1’s Master is strictly for your stage volume. And finally, when two
K1s are Linked (see 9) and additional instruments are connected to the second K1, you may
take the Bal. Line Out from either amp to feed the PA mixer.
11. Plug headphones into the Stereo Phones jack. The Phones mix will be in stereo for those
stereo input signals plugged into both of Channel 1’s inputs and the Aux. Inputs. Channel
2’s mono input signals will go to both phones as well, however Channel 3’s input signals
will not go to the phones as they are strictly for the K1’s amp/speaker system (see 4).
Power
Input Input
Mic
Aux Input
Out InInput
RL
CH
1
Gnd Lift
Grounded
15
+
15
-
0
5 5
10 10
15
+
15
-
0
5 5
10 10
15
+
15
-
0
5 5
10 10
15
+
15
-
0
5 5
10 10
CH
2
Bal. Line Out
Link
Stereo
Phones
CH
3
MON
B
a
s
s
G
a
i
n
L
/
M
o
n
o
M
o
n
o
R
T
r
e
b
l
e
B
a
s
s
G
a
i
n
G
a
i
n
T
r
e
b
l
e
M
a
s
t
e
r
R
L
Pan
0
4
6
1
3
7
9
2 8
5
10
1
0
0
1
0
0
1
0
0

Содержание

Похожие устройства

Скачать