![BSS BLU-101 [5/12] Front panel](/img/pdf.png)
BSS BLU-101 [5/12] Front panel
![BSS BLU-101 [5/12] Front panel](/views2/2008123/page5/bg5.png)
5
Front panel
Input/Output channel monitoring
Each channel has the following LED indicators:
Clip
Indicates clipping in the analogue domain for each input or output channel. The LED will
illuminate at +18.5dB.
Signal
The Signal LED will illuminate for each input or output channel when the signal reaches
or exceeds the signal threshold of -20dB.
Input channels have a third indicator:
48V
(Input channels only) Illuminates to indicate +48V phantom power has been activated for
the relevant input channel.
Other indicators
COM (Communications)
The COM LED turns green to indicate a normal linked condition. The COM LED blinks
green if data is being transferred on the Ethernet or RS232 port. The LED turns yellow if a
link is established but no IP address has been established.
STAT (Status)
The STAT LED turns green when a valid design file is loaded and running. The STAT
LED turns yellow when the design is paused. The STAT LED turns red when the design is
stopped.
ERR (Error)
The ERR LED is normally off. It turns red in the case of a critical or fatal error.
PWR (Power)
The PWR LED turns blue when the device is powered on. It blinks during locate
operations (both when pressing the locate button on the rear of the device and also when
locating the device from within the software).
Содержание
- A molded mains plug that has been cut off from the cord is 2
- Asta approved to bs1362 2
- Do not use the mains plug without the fuse cover in place 2
- Important safety instructions 2
- Read the following 2
- Replacement fuse covers can be obtained from your local 2
- Retailer replacement fuses are 13 amps and must be 2
- U k mains plug warning 2
- Unsafe discard the mains plug at a suitable disposal facility 2
- Warning for your protection 2
- Declaration of conformity 3
- Electromagnetic compatibility 3
- Important safety instructions 3
- Operation of this unit within significant electromagnetic fields should be avoided 3
- Safety instructions 3
- This device complies with part 15 of the fcc rules and the product specifications noted on the declaration of conformity operation is subject to the following two conditions 3
- This device may not cause harmful interference and 3
- This device must accept any interference received including interference that may cause undesired operation 3
- Use only shielded interconnecting cables 3
- An example of this equipment has been tested and found to comply with the following european and international standards for electromagnetic compatibility and electrical safety radiated emissions eu en55022 2006 immunity eu en55024 1998 electrical safety eu iec60065 01 amd1 electrical safety usa ul60065 06 4
- Do not remove covers no user serviceable parts inside refer servicing to qualified service personnel for continued compliance with international emc regulations it is important that all cables be screened and connected as follows audio cable screens to their blu device connector ground control cable screens to the ground screws adjacent to the connector network cables should be of type cat 5 fitted with a clip on ferrite sleeve stewart type 28a2029 0a0 near the network socket end this equipment must be earthed it should not be necessary to remove any protective earth or signal cable shield connections to prevent ground loops any such disconnections are outside the recommended practice of bss audio and will render the emc or safety certificate void 4
- If the unit is likely to undergo extreme vibration through extensive road trucking and touring the unit must be supported at the rear and or sides to lessen the stress on the front mounting flange rear rack supports are provided to reduce stress on front mounting flange damage caused by insufficient support is not covered by the warranty to prevent cosmetic damage to the front panel finish use protective plastic cups under the rack mounting bolts 4
- Important user information 4
- Mechanical installation 4
- Regulatory information 4
- Front panel 5
- Audio cable wiring 6
- Rear panel 7
- Ground 9
- Led relay 9
- Supply voltage 9
- Wire mode 9
- Technical specifications 10
Похожие устройства
- AUDIENT iD44 Руководство по эксплуатации
- ATC SCM150SL PRO Руководство по эксплуатации
- ATC SCM100SL PRO Руководство по эксплуатации
- Crown DSi 2000 Руководство по эксплуатации
- Behringer RX1602 EURORACK PRO Руководство по эксплуатации
- Behringer UCA202 U-CONTROL Руководство по эксплуатации
- Behringer MX400 MICROMIX Руководство по эксплуатации
- Behringer vmx100usb pro mixer Руководство по эксплуатации
- Behringer b215d eurolive Руководство по эксплуатации
- Behringer SX3242FX EURODESK Руководство по эксплуатации
- Behringer DJX900USB PRO MIXER Руководство по эксплуатации
- Behringer B205D EUROLIVE Руководство по эксплуатации
- Behringer DX2000USB PRO MIXER Руководство по эксплуатации
- Behringer B112D EUROLIVE Руководство по эксплуатации
- Behringer B212D EUROLIVE Руководство по эксплуатации
- Art SLA-2 Руководство по эксплуатации
- Behringer B115D EUROLIVE Руководство по эксплуатации
- Behringer B115MP3 EUROLIVE Руководство по эксплуатации
- Art MX624 Руководство по эксплуатации
- Behringer B615D EUROLIVE Руководство по эксплуатации