KRAFT KF-FDM454D901W [19/29] Посудомоечная машина dishwasher посудомоечная машина dishwasher

KRAFT KF-FDM454D901W [19/29] Посудомоечная машина dishwasher посудомоечная машина dishwasher
ПОСУДОМОЕЧНАЯ МАШИНА
DISHWASHER
ПОСУДОМОЕЧНАЯ МАШИНА
DISHWASHER
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
36 37
Attention!
After removing the work top, the screws must be screwed again under the rear edge of
the top (b). The height will then be reduced to 815 mm, as scheduled by the International
Regulations (ISO) and the dishwasher will fit perfectly under the kitchen working top.
Step 2. Tension adjustment of the door spring
1. The door springs are set at the factory to the proper
tension for the outer door. If aesthetic wooden panel are
installed, you will have to adjust the door spring tension. Rotate
the adjusting screw to drive the adjustor to strain or relax the
steel cable.
2. Door spring tension is correct when the door remains
horizontal in the fully opened position, yet rises to a close with
the slight lift of a finger.
Step 3. Cold water connection
Connect the cold water supply hose to a threaded ¾ (inch) connector and make
sure that it is fastened tightly in place. If the water pipes are new or have not been
used for an extended period of time, let the water run to make sure that the water
is clear. This precaution is needed to avoid the risk of the water inlet to be blocked
and damage the appliance.
The safety supply hose consists of the double walls. The hose’s system
guarantees it is intervention by blocking the flow of water in case of the supply
hose breaking and when the air space between the supply hose itself and the
outer corrugated hose is full of water.
WARNING! A hose that attaches to a sink spray can burst if it is installed on the same
water line as the dishwasher. If your sink has one, it is recommended that the hose be
disconnected and the hole plugged.
How to connect the safety supply hose
1. Pull The safety supply hoses completely out from storage compartment located at rear of
dishwasher.
2. Tighter the screws of the safety supply hose to the faucet with thread ¾ inch.
3. Turn water fully on before starting the dishwasher.
How to connect the safety supply hose
1. Turn off the water.
2. Unscrew the safety supply hose from the faucet.
Step 4. Connection of drain hoses
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink,
making sure to avoid bending or crimping it. The height of drain pipe must be less than 1000 mm.
The free end of the hose must not be immersed in water to avoid the backflow of it.
How to drain excess water from hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly into
the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container
that is held outside and lower than the sink.
Water outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks. Ensure
that the water drain hose is not kinked or squashed.
Extension hose
If you need a drain hose extension, make sure to use a similar drain hose. It must be no longer
than 4 meters. Otherwise the cleaning effect of the dishwasher could be reduced.
Syphon connection
The waste connection must be at a height less than 100 cm (maximum) from the bottom of the
sink. The water drain hose should be fixed.
Step 5. Levelling the dishwasher
Dishwasher must be level for proper dish rack
operation and wash performance.
1. Place a spirit level on door and rack track inside
the tub as shown to check that the dishwasher
is level.
2. Level the dishwasher by adjusting the three
levelling legs individually.
3. When leveling the dishwasher, please note that
the dishwasher does not tip over. The maximum
adjustment height of the feet is 50 mm.
4. The height of the rear legs can be changed by
screwing.

Содержание

Похожие устройства

Скачать