Brayer 4220BR [5/23] 9 en en
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Brayer 4220BR [5/23] 9 en en

Brayer 4220BR [5/23] 9 en en
8 9EN EN
USING THE ATTACHMENTS
Floor/carpet brush (1)
When using the brush (1) set the switch (2) to the
necessary «FLOOR/CARPET» position.
Crevice nozzle (24)
The nozzle (24) is used for cleaning radiators, chinks or
spaces between cushions.
Furniture/furniture upholstery brush (25)
The attachment (25) is intended for cleaning fabric
surfaces of upholstered furniture and for collecting dust
from furniture surface, the pile on the brush (25) prevents
damage of polished furniture surface. During operation
install the brush on the attachment (25).
ASSEMBLING THE VACUUM CLEANER
Attaching and removing the exible hose (7)
• Insert the exible hose (7) ending (8) into the air inlet
(10) until the locks (9) catch.
• To remove the exible hose (7), press the locks (9) and
detach the ending (8) from the air inlet (10).
Attaching the telescopic pipe (4) and the attachments
• Attach the telescopic extension pipe (4) to the exible
hose handle (5).
• Extend the lower part of the telescopic extension pipe
(4) to the required length, having preliminarily pressed
the lock (3) (pic. 2).
• Choose the necessary attachment – oor/carpet brush
(1), crevice nozzle (24) or upholstery attachment (25) –
and attach it to the telescopic extension pipe (4).
• You can attach the attachments (24 and 25) to the
exible hose handle.
ATTENTION!
• Do not use the vacuum cleaner in places where
aerosols are used or sprayed and in proximity to highly
inammable liquids, do not use the vacuum cleaner in
the places where such liquids are stored.
• The vacuum cleaner is not intended for collecting water
or any other liquids; do not use it for collecting burning
or smoking cigarettes or cinders.
• Do not use the vacuum cleaner for collecting dust of
plaster, concrete, our or ashes.
• Take sharp objects away from the oor before cleaning
to prevent damage to the unit.
• If the suction power of the vacuum cleaner decreases
rapidly while cleaning, switch it o immediately, unplug
it and check the telescopic pipe (4) or the exible hose
(7) for obstruction. Remove the obstruction, after that
you can resume cleaning.
USING THE VACUUM CLEANER
Attention!
Switch the vacuum cleaner on only with the dustbag (15 or
disposable paper dustbag 26) and the inlet (16) and outlet
HEPA (21) lters installed.
• Before cleaning always make sure that the lters (16,
21) are installed properly.
• Take the power plug and unwind the power cord to the
required length, connect the power plug to the mains
socket.
• The yellow mark on the power cord indicates the
maximum cord length. Do not pull out the power cord
further than the red mark.
• Press the on/o button (20) to switch the vacuum
cleaner on.
• While cleaning, you can control the suction power
using the manual suction power control (6) on the
exible hose handle (5) and with the suction power
control buttons «+/-», the digits «1-2-3-4-5» on the
display (17) will show the suction power level, the
optimum suction power ratio and the surface type for
cleaning will be shown with the symbols in the upper
line of the display (17) (pic. 1).
• After you nish cleaning, switch the vacuum cleaner o
by pressing the on/o button (20) and unplug it.
• To wind the power cord, press the button (18); keep a
hold of the winding cord with your hand.
• If you have to make a break during the cleaning,
switch the vacuum cleaner o by pressing the button
(20) and install the brush (1) to the brush storage (19)
(pic. 3).
ATTENTION!
Before changing the attachments or cleaning the
dust bin (15), switch the vacuum cleaner o by
pressing the on/o button (20) and unplug it.
CLEANING AND MAINTENANCE
Cleaning the dustbag (15)
• If during cleaning the dustbag-full symbol appears
on the display (17) (pic. 2), clean the dustbag (15) or
replace the disposable paper dustbag (26).
Note: the paper dustbag (26) is disposable, when the
dustbag (26) is full, dispose of it.
• Before cleaning the dustbag (15), switch the vacuum
cleaner o by pressing the on/o button (20) and unplug
it.
• Open the dustbag compartment lid (13) by pressing the
lid lock (12).
• Remove the dustbag holder (14) with the dustbag (15).
• Take the dustbag (15) out from the holder (14).
• Place the dustbag (15) above the garbage bin, remove
the plastic clamp and clean the dustbag (15) of garbage
and dust. You can wash the dustbag (15) with warm
water and soft detergent, rinse and dry thoroughly. After
that install the plastic clamp on the dustbag (15).
• Install the dustbag (15) into the holder (14).
• Put the dustbag holder (14) with the dustbag (15)
installed into the dustbag compartment body.
• Close the dustbag compartment lid (13) and slightly
press on the lid (13) until the lock (12) clicks.
Notes:
– do not try to close the lid (13) without the dustbag holder
(14) installed, otherwise you can damage the lock or the
lid (13);

Содержание

Похожие устройства

Скачать