Deerma DEM-YS10W [6/13] Cleaning and maintenance error causes solutions

Deerma DEM-YS10W [6/13] Cleaning and maintenance error causes solutions
Cleaning and Maintenance Error&Causes &Solutions
Pay attention to environmental
protection
1. Clean the water outlet, filter and filter cup
A. Turn off the power button,and unplug from outlet.
B. Some metal parts may still be hot,don t touch by hand before cooling
down.
C. Remove the filter, pour out the coffee powder, and clean the filter and
filter cup with warm water with detergent. Do not put the filter and filter cup
in the dishwasher for cleaning.
D. Wipe the lower end of the water outlet with a wet cloth or tissue, clean
any possible residual coffee powder.
E. Install the filter (without filter cups) back to the outlet head.
F. Place a 200ml empty cup under the filter.
G. Boiling a few more cups with the coffee making mode,which can achieve
the effect of cleaning.
H. If don t use the filter after cleaned, please do not install back the filter
head, otherwise the tightness between the two will be reduced.
2. Clean the water tank
Remove the water tank and pour out the remaining water. It is
recommended to empty the water tank before and after use. Clean the tank
with warm water with detergent, clean thoroughly and dry. Do not put the
tank in the dishwasher for cleaning.
3. Clean the product
Wipe the enclosure with a wet soft cloth. Do not clean with abrasive
detergent or cleaning cloth to avoid scratching the surface of the product.
Warning: Do not immerse this product in water or other liquids.
4. Calcium removal
Minerals deposit will affect the heating performance of appliances,need
remove the calcium after using for a certain time---- Add calcium remover
into the water tank and shake the remover with warm water below 30 ℃ to
avoid particles, then use boiling hot water method to pump out the water in
the water tank, add purified water into the water tank (fill the water tank)
again, boiling coffee and hot water more times, to achieve the effect of
cleaning the tube(must use 2 tanks of water during cleaning).
All products bearing this symbol are waste electrical and
electronic equipment (WEEE as in directive 2012/19/EU) which
should not be mixed with unsorted household waste. Instead,
you should protect human health and the environment by
handing over your waste equipment to a designated
collection point for the recycling of waste electrical and
electronic equipment, appointed by the government or local
authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. Please contact the installer or local authorities
for more information about the location as well as terms and
conditions of such collection points.
Error Causes Solutions
No coee
ow out
1. No water in the water
tank ;
2. The coee powder is
too ne;
3.Excessive coee powder;
4. Haven’t turn on the
power;
5. The coee powder is
pressed too tightly.
1.The lter is not turned to
the locked position;
2.Residual coee powder
at the edge and top of the
lter cup.
1.Turn the lter to the
locked indicated position;
2.Clean the residual coee
powder at the edge of the
lter cup and sealing ring.
1. The coee powder is
too thick;
2. Less coee powder in
lter cup.
1. Choose coee powder
with appropriate thickness;
2. Increase the appropriate
amount of coee powder
into the lter cup.
1.Excessive coee powder
in lter cup;
2. The coee powder is
too ne.
1. Adjust the appropriate
amount of powder in the
lter cup;
2. Adjust the thickness of
coee powder properly.
1. Add corresponding
amount of water to the
water tank;
2. Grind the coee powder
to the proper thickness;
3. Reduce the amount of
coee powder
appropriately;
4. Plug the power into
socket and turn on the
power switch.
5.Rell the coee powder,
which do not press too
hard.
Coee ows
to the edge
of the lter
Coee
comes out
too fast
Coee
comes out
too slow
09 10

Похожие устройства