Rondell RDE-1050 [6/24] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Rondell RDE-1050 [6/24] English

Rondell RDE-1050 [6/24] English
6
ENGLISH
•
Insert the power cord connector (16) into the socket (12) on
the thermopot body and the power cord (16) plug into the
mains socket. You will hear a sound signal, and all indicators
on the control panel (5) will light up for 5 seconds. After that
the thermopot will be switched on in the «Tap water» mode with
the preset temperature 80°С, and the buttons (22, 23, 24, 25,
26, 27) indicators will glow constantly.
Temperature selection
To change the desired keep warm temperature, press the tem-
perature selection button (26) «Т°С selection». You can select the
keep warm temperature «100°С -90°С-80°С-60°С-50°С-40°С».
•
The preset keep warm temperature is shown by the corre-
sponding indicators (19).
Water type
•
The thermopot has 2 water type modes: tap water and drinking
water. You can select the modes with the button (23). One of
the indicators (21) will indicate the water type.
Tap water mode: first the water is boiled, and then it cools down
to the preset temperature.
Drinking water mode: direct heating to the preset tempera-
ture and when the temperature reaches the preset value, heat-
ing stops.
ECO mode
•
The thermopot also has ECO mode. You can select this mode
with the button (22). This mode is indicated with the indica-
tor (20).
•
ECO mode is energy saving. You can switch it off by pressing
the button (20) again.
Boiling
•
Select the temperature with the button (26), the water type
with the button (23) and the mode with the button (22).
•
Press the button (27) again to confirm the selected tempera-
ture, water type and mode. After that boiling will start which
is indicated with the indicator (17) on the control panel (5).
•
After long water boiling you will hear 3 sound signals and the
thermopot will switch to the keep warm mode, the indicator
(17) «BOILING» will go out and the keep warm mode indicator
(18) «Keep warm» will be flashing.
•
If the water temperature goes significantly below the preset
temperature, for instance, if you added some cold water, the
boiling mode will be switched on, the indicator (17) «BOILING»
will light up. After boiling the water temperature will be main-
tained depending on the preset value and will be shown with
the indicators (18).
Blocking
•
The thermopot is equipped with the water dispensing block-
ing function.
•
This function is available after pressing the button (24).
•
Drain the water; to do this, you must unlock the activation of
the water pump by pressing button (24) «UNLOCK», the button
(24) indicator “ ” will light up.
Attention! Be careful when pouring out water to avoid burns
by hot water.
Version 1:
–
place a suitable bowl, for instance, a cup under the spout for
pouring water (4) and press the water dispense button (3).
Version 2:
–
place a suitable bowl under the spout for pouring water (4) and
press the water dispense button (25) «DISPENSE».
•
To switch the thermopot off, press the button (27).
•
To disconnect the thermopot from the mains, disconnect the
power plug (16) from the mains socket.
•
Open the thermopot lid (8) and wait until it cools down com-
pletely, remove the lid (8) (see the chapter BEFORE THE FIRST
USE), drain the water, install the lid (8) back to its place and put
the thermopot away for storage.
Overheating protection
•
If you accidentally switched the thermopot on and the water
level is below the minimal mark “MIN”, the automatic thermal
switch will be on, you will be hearing sound signals for 20 sec-
onds and all indicators on the control panel (5) will be flash-
ing. In this case unplug the thermopot and let it cool down for
10-20 minutes, then fill it with water, and switch the thermopot
on, the unit will operate in normal mode.
CLEANING AND CARE
•
Before cleaning, disconnect the thermopot from the mains,
pour out water and let the thermopot cool down completely.
•
Before removing the lid (8) open it and pull the lid (8) to the
control panel (5).
•
Carefully tilt the thermopot to drain the remaining water.
•
Install the lid (8) back to its place. To do it, place the lid (8)
at a small angle and install the lid (8) to its installation place.
Before using the thermopot make sure that the lid (8) is fixed
properly.
•
Clean the outer surface of the thermopot with a slightly damp
cloth and then wipe it dry.
•
Use neutral detergents to remove dirt; do not use metal
brushes, abrasive detergents and solvents.

Содержание

Похожие устройства

Скачать