Smartmi Air Purifier P2 (ZMKQJHQP21) [5/36] Turn battery power off on
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Smartmi Air Purifier P2 (ZMKQJHQP21) [5/36] Turn battery power off on

Smartmi Air Purifier P2 (ZMKQJHQP21) [5/36] Turn battery power off on
06
Power on/ Standby
Timing
Switching mode Adjust the display brightness/
night light.
Touch the Power on/ Standby
Button to turn it on.
In the power-on state, touch
the Power on/ Standby Button
to turn it o.
When the device is turned on,
touch the Timing Button to cycle
through "1h-2h-4h-8h-cancel"
and start the timer. The device will
automatically switch to Standby
after the timer has run out.
When the device is turned on,
touch the Mode Button to cycle
through operating modes.
When the device is turned on,
touch the Brightness Button to
cycle through the options for
screen brightness (full brightness,
half brightness, and o). Press and
hold the Brightness Button for 3s to
dim the night light. Press and hold
for another 3s to gradually turn up
the night light.
Use
Prompt: When powered on, the device
uses the power adapter to supply power
and charge the battery; when the device
is unplugged, the battery is automatically
activated. The whole device switches o
after the battery power has been used up.
Turn battery power o/on
Battery level indication and charging
Press and hold the Brightness Button and
the Power on/ Standby Button at the same
time for 5s. The battery power can be turned
o/on after the purifier has beeped.
Connected to a power supply
After the purifier has been
connected to the power
supply, the screen will be as
shown in the figure on the
right and then return to the
main interface or shut o.
Fully charged
When the purifier is fully
charged, the screen will be
as shown in the figure on the
right and then return to the
main interface or shut o.
Battery powered
When the power is cut o
after the device has been
turned on, the screen will be as
shown in the figure on the right
and then return to the main
interface.
Prompt: The main interface will display the time
remaining after it has been set.
Prompt: Adjust the night light
RGB color in the app
07
Use
Resetting Wi-Fi
ScreensaverResetting Purifier
Turning Wi-Fi On/O
Press and hold the
Mode Button and
Timing Button at the
same time for 5s. The
Wi-Fi can be reset
after the purifier has
beeped.
A screensaver animation is displayed
after 60s of no operation, and the
screensaver color reflects the air
quality. Press any button to restore to
its previous state.
Hold down the "Switching Modes"
and "Power on/ Standby" buttons
simultaneously for 10 seconds. After
you hear a sound, the purifier has been
reset successfully.
Press and hold the
Timing Button for 5s.
The Wi-Fi can be
turned o/on after the
purifier has beeped.
Note:
Open the Home app on your iPhone/iPad.
Tap "Add Accessory" and then scan the HomeKit setup code on the
product sticker (two stickers on the device unit, see illustration), or enter
the eight-digit setup code above the HomeKit Setup Code. The device
will then be linked to the Apple Home app.
The device can be linked to Smartmi
Link after linking to HomeKit. Go to the
Personal Info page on Smartmi Link. Tap
"HomeKit Info" and then link the HomeKit
device as prompted.
Devices linked to Smartmi Link can also
be added to HomeKit. Go to the Device
Control page on Smartmi Link. Tap "Add
to HomeKit" in "Settings" and then link
the device to HomeKit as prompted.
Note:
Please ensure that your Wi-Fi network is
both available and has Internet access.Place
your phone as close to this product as possible.
(This product does not support 5G networks).
To control this accessory which is compatible
with HomeKit, it is recommended to use iOS 13.0
or a later version.
Please keep the HomeKit setup code, as you
will need to scan the code to link the device to
HomeKit after a factory reset.
iPad and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Controlling this HomeKit-enabled accessory
automatically and away from home requires a
HomePod, Apple TV, or iPad set up as a home
hub. It is recommended that you update to the
latest software and operating system.
1
2
This product has been linked to the
Smartmi Link and can be controlled
using the app.
Scan the QR code or search for
"Smartmi Link" on the app store to
download and install the app. Go to
the app's homepage, click "+" in the
middle of the page, then add the
device as prompted.
Please ensure that your Wi-Fi network is both
available and has Internet access. Place your
phone as close to this product as possible. (This
product does not support 5G networks).
This product will be listed as "Smartmi Air Purifier
P2" in the app's device listing.
HomeKit Setup Code
Intelligent Control with Apple HomeKitLinking the Device to Smartmi Link

Содержание

Похожие устройства

Скачать