![Coolfort CF-4001 9 BTU [21/28] English](/img/pdf.png)
Coolfort CF-4001 9 BTU [21/28] English
![Coolfort CF-4001 9 BTU [21/28] English](/views2/1860893/page21/bg15.png)
21
ENGLISH
The moisture condensed on the back of the internal unit is
collected in a storage tank and removed from the room. Do
not put anything in the tank.
Attention!
– Connect the internal unit first, and then the external one.
– Do not let the pipelines protrude from the back of the
inner block.
– Do not let the drain hose sag.
– Insulate the pipes (15, 17) (fig. 11).
– Make sure that the drain hose is located at the bottom
of the bundle. If you place it at the top, water can leak
inside the unit.
– It is forbidden to cross and twist the power cable with
any other wires.
– Lay the drain hose at an angle to drain the condensed
water.
– Connect the tubes of the inner block with two wrenches
(fig. 11, 13 ). Pay special attention to the permissible
torque (tightening force), as shown in the table below,
so that the freon tubes, connectors and coupling nuts
do not deform.
– First tighten them with your fingers, then use wrenches.
Model Pipe size Tightening
torque,
(kg.m)
Nut
size,
(mm)
CF-4000, CF-4001,
CF-4002
∅ 6 or 1/4” 1.8 17
CF-4000, CF-4001 ∅ 10 or 3/8” 3.5 22
CF-4002 ∅ 12 or 1/2” 5.5 24
POWER CORD AND CONTROL CABLE
CONNECTION (fig. 12)
Inner block
Connect the power cable (19) and the control cable (20)
separately to the indoor unit terminal block (2) according
to the outdoor unit connection.
When connecting the wires to the terminal board of the
inner block, use the attached connection diagram (see
Appendix 1).
Outer block
1) Remove the indoor unit control panel access cover
(24) (fig. 12) by loosening the screw. Connect the wires
of the control cable and the power cable to terminals
on the terminal block following the connection diagram
(see. Annex 1).
2) Fasten the cables on the control panel with a cable
clamp.
3) Install the cover in its original position and secure it
with a screw.
Attention!
Make sure the power cable section corresponds to the
model specification (see the cable specification table
below).
Models Power cord Control cable
Type Sectional
area/
quantity
Type Sectional
area/
quantity
CF-4000,
CF-4001
HOSVV-F 1.0 mm
2
х3 H07RN-F 1.0 mm
2
х3
CF-4002 HOSVV-F 1.5 mm
2
х3 H07RN-F 1.5 mm
2
х3
INSTALLATION OF THE OUTER BLOCK
Install the drain port and the drain hose
– Install the drain and drain hose for condensate outlet.
– Condensate drips out of the outdoor unit when the unit
is in the heating mode. Not to disturb neighbors and to
protect the environment, install the drain port and the
drain hose to drain condensate. Just install the drain
port and a rubber washer on the outdoor unit chassis,
then connect the drain hose to the port (fig. 14).
– Fix the chassis on a flat and solid floor with bolts and
nuts. When installing the outer block on a wall or roof,
make sure that the support is securely fixed so that it
does not shake due to strong vibration or strong wind.
– Remove the caps from the 2-way and 3-way valve.
– Connect the freon pipes (15, 17) separately to the 2- (29)
and 3-way (26) valves according to the required torque.
VACUUMING OF THE ROUTE
Cleaning from moisture with a vacuum pump
Air containing moisture remaining in the refrigeration
cycle may cause malfu nction of the air conditioner.
After connecting the inner and outer blocks, remove air
and moisture from the heat exchanger of the inner block
and freon tubes using a vacuum pump and a gauge
manifold (fig. 15).
– Unscrew and remove the plugs (28) from the 2- and
3-way valves.
– Unscrew and remove the cap from the service valve.
– Connect the vacuum pump flexible hose to the service
port (27) of the 3-way valve (26). 3-way valve diagram
(fig. 16).
– Turn on the vacuum pump for 10-15 minutes until abso-
lute vacuum of 10 mm Hg is reached.
– While the vacuum pump is running, close the handle of
the low pressure valve on the collector of the vacuum
pump. Then turn off the vacuum pump.
– After the air is pumped out, wait 5-10 minutes and use
the gauge manifold to make sure the system is tight.
FILLING THE SYSTEM WITH FREON
Use a 6-sided wrench to open the valves of the outer
block.
– Open the 2-way valve for 1/4 turn, then close it after
10 seconds. Check the tightness of all joints.
– Unscrew the rods of the 2- and 3-way valves complete-
ly. Disconnect the vacuum pump flexible hose.
– Install and tighten all valve plugs back up.
ELECTRICAL SAFETY AND CHECKING
FOR GAS LEAKS
Checking of electrical safety
After the installation is complete, perform the electrical
safety check:
1. Insulation resistance. The insulation resistance must
be more than 2 megohms.
2. Grounding After the grounding work is completed,
measure the grounding resistance visually and with a
special tester. Make sure that the ground resistance is
below 4 ohms.
3. Checking for leakage currents (performed during a test
turn-on). During the test turn-on after the installation is
completed, a specialist can check for leakage currents
using a sensor and a multimeter. If there is a leak, the
unit should be turned off immediately. After that, you
need to find and eliminate the cause of the problem.
Содержание
- Cf 4000 1
- Installation manual 1
- Www coolfort ru 1
- Инструкция по установке 1
- Do not repair the unit by yourself do not disassemble 3
- English 3
- The unit by yourself if any malfunction is detected or after it has fallen unplug the unit and apply to any authorized service center at the contact addresses given in the warranty certificate and on the website www coolfort ru 3
- English 4
- English 5
- English 6
- Air conditioner operating conditions 7
- Clean the filters and other parts wipe the dust off the outdoor unit touch up rusted areas on the outdoor unit to prevent rust from spreading 7
- Delivery set indoor unit 1 pc instruction manual 1 pc mounting kit 1 pc screws dowels remote control rc 1 pc 2 aaa batteries included mounting plate 1 pc outdoor unit 1 pc outdoor unit is delivered filled installation kit 1 pc includes protective sleeve insulating tape deflator overflow drain pipe and seals copper pipes for freon lines drain hose and brackets for 7
- English 7
- For environment protection do not throw out the unit and the batteries if included do not discard the unit and the batteries with usual household waste after the service life expiration apply to specialized centers for further recycling the waste generated during the disposal of the unit is sub ject to mandatory collection and consequent disposal in the prescribed manner for further information about recycling of this product apply to a local municipal administration a disposal service or to the shop where you purchased this product 7
- Guarantee details regarding guarantee conditions can be obtained from the dealer from whom the appliance was purchased the bill of sale or receipt must be produced when making any claim under the terms of this guarantee 7
- Installing the outdoor unit are sold separately 7
- Ples of the unit operation without a preliminary notification due to which insignificant differences between the manual and product may be observed if the user reveals such dif ferences please report them via e mail info coolfort ru for receipt of an updated manual 7
- Recycling 7
- Remote control power supply 3v 2 aaa batteries included in the delivery set 7
- Technical specifications air conditioner 7
- The manufacturer preserves the right to change design structure and specifications not affecting general princi 7
- This product conforms to the emc directive 2014 30 eu and to the low voltage directive 2014 35 eu 7
- Unit operating life is not less than 3 years 7
- Русский 8
- Русский 9
- 33 последовательным нажатием кнопки 23 10
- Mode выберите автоматический режим работы символ 32 10
- В автоматическом режиме кондиционер в зависимо 10
- Включение кондиционера в автоматическом режиме 10
- Воздушного потока вентилятора auto автома тическая низкая средняя 10
- Высокая скорость 10
- Димое значение температуры в диапазоне от 16 до 30 с 10
- Для включения функций sleep timer turbo light 10
- Или нагрева 10
- Инструкция по эксплуатации кондиционер работает путем автоматического выбора режима работы нагрев осушение вентиляция охлаждение в зависимости от температуры в поме щении при запуске 10
- Кальных жалюзи 6 10
- Кнопками 25 и 24 установите необхо 10
- Кнопкой 23 mode выберите режим охлаждения 10
- Кнопкой 26 fan установите требуемую скорость 10
- Кнопкой 27 установите режим работы верти 10
- На дисплее пду загорится символ работы кондици онера в режиме нагрева 36 или охлаждения 10
- Нагрева создавая комфортные условия для поль зователя 10
- Нажмите кнопку 22 on off на пду 10 при этом 10
- Нажмите соответствующие кнопки 10
- Порядок управления 10
- После подключения кондиционера к электрической 10
- Последовательным нажатием кнопки 23 mode выбе 10
- Примечание в режиме auto значение температуры устанавливается автоматически и с пульта не задается 10
- Примечание в случае неисправного пду вы можете включить кондиционер в автоматическом режиме с помощью кнопки аварийного управления 21 для этого нажмите и удерживайте аварийную кнопку 21 на вну треннем блоке до включения кондиционера 10
- Примечание при последующих включениях работа в автоматическом режиме может быть выполнена только нажатием кнопки 22 on off 10
- Режим работы и температура определяются температурой в помещении 10
- Русский 10
- Сети нажмите кнопку 22 on off для включения на дисплее пду при этом появится символ 41 ото бражающий соответствующее текущее состояние 10
- Сти от температуры воздуха в помещении автомати чески начинает работать в режиме охлаждения или 10
- Установка температуры нажмите кнопку 22 on off на пду 10 при этом на дисплее пду загорится символ работы кондиционера в режиме нагрева 36 или охлаждения 33 10
- Русский 11
- Перегрев электрических проводов и штепселя 12
- Питания 12
- Рекомендуется производить каждые шесть меся цев 12
- Русский 12
- Русский 13
- Installation manual 14
- Инструкция по установке 14
- Рис 1 14
- Рис 2 рис 3 15
- Рис 4 рис 5 15
- Рис 6 рис 7 15
- Рис 8 рис 9 15
- Рис 10 рис 11 16
- Рис 12 16
- Рис 13 16
- Рис 14 16
- Рис 16 рис 15 16
- English 18
- English 19
- English 20
- Air containing moisture remaining in the refrigeration cycle may cause malfu nction of the air conditioner after connecting the inner and outer blocks remove air and moisture from the heat exchanger of the inner block and freon tubes using a vacuum pump and a gauge manifold fig 15 21
- English 21
- 22 on the remote controller 22
- Checking for gas leaks 1 soapy water method using a soft brush apply 22
- Checking the operational capability of all functions 1 turn on the unit by pressing the on off button 22
- English 22
- Gas system are fully open 22
- Leak sensor the presence of leaks can be checked 22
- Ly attached and the pipelines are properly con nected 22
- Make sure that the electrical wires are proper 22
- Make sure that the service valves of the liquid and make sure that the service valves of the liquid and 22
- Soapy water or neutral liquid detergent to the con nections of the internal and external unit to check the pipeline connections for leaks the appearance of bubbles indicates the presence of a leak 22
- Test turn on 22
- Using a special sensor 22
- Русский 23
- Русский 24
- Русский 25
- Cf 4000 cf 4001 hosvv f 1 mm 2 х3 h07rn f 1 mm 2 х3 26
- Cf 4002 hosvv f 1 mm 2 х3 h07rn f 1 mm 2 х3 26
- Модели шнур питания кабель управления 26
- Русский 26
- Тип площадь сечения количество 26
- Русский 27
- Ских проводов и надлежащем соединении трубо проводов 27
- Убедитесь в правильном подключении электриче 27
Похожие устройства
- Coolfort CF-4002 12 BTU Инструкция по эксплуатации
- Rommelsbacher EM 150 Руководство по эксплуатации
- Clatronic EM 3062 weis Руководство по эксплуатации
- Worx WX843.9 Руководство по эксплуатации
- Smeg SE264TD1 Руководство по эксплуатации
- Smeg SOP6101S2N Руководство по эксплуатации
- Smeg SOP6102S2PS Руководство по эксплуатации
- Smeg SOP6102TN Руководство по эксплуатации
- Smeg SOP6301S2X Руководство по эксплуатации
- Smeg ST363CL Руководство по эксплуатации
- Smeg STL323BL Руководство по эксплуатации
- Smeg STL333CL Руководство по эксплуатации
- Smeg FAB28RPG5 Руководство по эксплуатации
- Toshiba MV-TC26TF(BK) Руководство по эксплуатации
- Karcher K 4 Compact UM (1.679-406.0) Руководство по эксплуатации
- Hi Тройная волна HTG-5301 Руководство по эксплуатации
- Dyson Supersonic HD07 яркий никель/медь Инструкция по эксплуатации
- Dyson Supersonic HD07 Iron/Fuchsia Инструкция по эксплуатации
- Rowenta x KARL LAGERFELD Conical Wave CF324LF0 Руководство по эксплуатации
- Samsung MG23K3575AK/BW Руководство по эксплуатации
Скачать
Случайные обсуждения