Coolfort CF-4002 12 BTU [4/28] English

Coolfort CF-4002 [4/28] English
4
ENGLISH
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.
COMMERCIAL USAGE AND USAGE IN PRODUCTION AR-
EAS AND WORK SPACES IS PROHIBITED.
PREPARATION BEFORE USE
Remote control (10)
Remote control transmits control signals to the system.
Battery installation
Remove the battery compartment lid following the arrow
direction.
Insert new batteries, making sure the (+) and (-) of the
batteries are correctly matched.
Install the cover and shift it to its place (fig. 1).
Note:
Use 2 AAA batteries (1.5 V). Do not use rechargeable
batteries. Replace the batteries with new ones of the
same type when the display becomes dim.
Do not use an exhausted battery and a new one at
the same time, as well as batteries of different types.
Service life of the batteries is no more than 1 year.
If you are not going to use the remote control for a long
time, remove the batteries and store the remote control
and batteries separately in a safe and dry place.
BEFORE USING THE AIR CONDITIONER, ALWAYS
CHECK AND SET THE FOLLOWING:
Presetting the remote control (RC)
The remote control (10) is NOT preset by the manufac-
turer for cooling or heating.
Every time after replacing the batteries in the remote
control or when turning the power on, the heating sym-
bol (36) « » or the cooling symbol (33) « » will flash
on the remote control display.
The user can pre-set the remote control as follows:
If you press any RC button while the heating sym-
bol (36) « » is flashing, the heating mode will be
selected.
If you press any button on the remote control while the
cooling symbol (33) « » is flashing, the cooling mode
will be set.
If you do not press any button for 10 seconds, the remote
control will be automatically set to the heating mode.
Presetting Auto Restart
Note: An automatic restart after a power failure and subse-
quent restoration of the power supply resumes system op-
eration with the same parameters as before the shutdown.
Presetting auto restart with
the emergency control button (21)
The unit is not factory-configured to be automatically restarted.
If auto-restart is required, follow these steps to enable this
feature:
1) Make sure the air conditioner is switched off;
2) Press and hold the emergency control button (21) on
the indoor unit until the air conditioner is switched on.
3) Continue to hold the emergency control button (21) for
more than 10 seconds until you hear three short beeps.
Auto restart will then be activated. To cancel auto restart,
repeat the above steps until you hear four beeps.
Presetting auto restart with the remote control
The unit is factory-preconfigured to be automatically re-
started.
If auto-restart is not required, follow the steps below to dis-
able this feature:
1) Make sure the air conditioner is switched on;
2) Press the «SLEEP» button (31) 10 times within 8 sec-
onds until you hear 3 short beeps.
Auto restart will then be canceled. To activate auto restart,
repeat the above steps until you hear 4 short beeps.
AIR CONDITIONER REMOTE CONTROL
The air conditioner is controlled by the remote control (RC) (10).
To control the room air conditioner, point the remote
controller at the indoor unit remote control signal receiv-
er panel (19).
When operating the remote control, the distance
between the remote control and the indoor unit of the air
conditioner should be no more than 7 meters.
At the time of signal transmission between the remote
control and the indoor unit, there should be no obstacles
that interfere with the signal transmission.
The remote control should be at least 1 meter away from
television and radio equipment.
Do not drop or bump the remote control, do not leave it
under direct sunlight.
Button Description
(21) «Emergency control» Turning on the air conditioner in the «AUTO» mode, setting auto restart in case of power failure
(22) «ON/OFF» Used to switch the air conditioner on and off
(23) «MODE»
Used to select operating modes: Auto , Cooling , Dehumidification , Ventilation
and Heating .
(24) « »
Pressing the button decreases the value of the set indoor air temperature by 1 °C, respective-
ly. To quickly change the temperature, press and hold the button for more than 2 seconds.
The button can also set the timer
(25) « »
Pressing this button increases the value of the set indoor air temperature by 1 °C, respectively.
To quickly change the temperature, press and hold the button for more than 2 seconds.
The button can also set the timer
(26) «FAN»
Used to select the fan speed of the indoor unit: automatic AUTO, high , medium
and low
(27) « »
Vertical louvre lifting control button
(28) «TIMER»
If the air conditioner is switched off or on, pressing the TIMER button sets the timer to switch
the air conditioner on or off, the «ON» symbol will start flashing. Each time the button (25)
« » or (24) « » is pressed, the time for switching the air conditioner on increases or
decreases by 30 minutes.
(29) «TURBO»
Pressing this button activates the enhanced cooling or heating mode. In this case, the internal
fan starts to rotate at an increased speed relative to the available speed modes.

Содержание

Похожие устройства

Скачать
Случайные обсуждения