Makita 18В, Li-ion DPB184Z [8/68] Assembly

Makita DPB184Z [8/68] Assembly
8 ENGLISH
Hook
CAUTION: Never hang the tool at high or
potentially unstable location.
The hook is convenient for hanging the tool temporarily.
To use the hook, simply lift up hook until it snaps into
the open position.
When not in use, always lower hook until it snaps into
the closed position.
Open position
►Fig.3: 1. Hook
Closed position
►Fig.4: 1. Hook
Switch action
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
WARNING: NEVER defeat the lock-o󰀨 button
by taping down or some other means.Aswitchwith
anegatedlock-o󰀨buttonmayresultinunintentional
operationandseriouspersonalinjury.
WARNING: NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-o󰀨 button.Aswitchinneedofrepair
may result in unintentional operation and serious
personalinjury.ReturntooltoaMakitaservicecenter
forproperrepairsBEFOREfurtherusage.
Topreventtheswitchtriggerfrombeingaccidentally
pulled,alock-o󰀨buttonisprovided.Tostartthetool,
depressthelock-o󰀨buttonandpulltheswitchtrigger.
Toolspeedisincreasedbyincreasingpressureonthe
switch trigger. Release the switch trigger to stop.
►Fig.5: 1.Lock-o󰀨button2. Switch trigger
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeingpulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
►Fig.6: 1. Lamp
NOTE: Do not apply impact to the lamp, which may
cause damage or shorted service time to it.
NOTE:Useadryclothtowipethedirto󰀨thelensof
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE:Whenthetoolisoverheated,thelampblinks
foroneminute,andthengoeso󰀨.Inthiscase,cool
downthetoolbeforeoperatingagain.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched o󰀨 and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the band saw blade
CAUTION:
Oil on the band saw blade can cause the
blade to slip or come o󰀨 unexpectedly. Wipe o󰀨 all excess
oil with a cloth before installing the band saw blade.
CAUTION: Always wear protective gloves
when handling the band saw blade.
CAUTION:
Use caution when handling the band saw
blade to avoid cut by the sharp edge of the blade teeth.
CAUTION:
Keep your body away from the band
saw blade when checking the blade movement.
CAUTION: When turning the blade tightening
lever clockwise to release the tension on the band
saw blade, point the tool downward because the
band saw blade may come o󰀨 unexpectedly.
Toinstallthebandsawblade:
1. Turnthebladetighteningleverclockwiseuntilit
stops to loosen the wheel.
►Fig.7: 1. Tighten 2. Loosen 3. Blade tightening lever
2. Openthewheelcover.
►Fig.8: 1. Wheel cover 2. Hook
NOTICE: When opening the wheel cover, open
and release both the hooks simultaneously.
Opening only one hook may cause crack on the
wheel cover.
3. Matchthedirectionofthearrowsonthebandsaw
bladeandonthewheels.
4. Insertthenon-serratedsideofthebandsawblade
into the upper holder and lower holder. Make sure the
bandsawbladeinbothupperandlowerholdertouches
tothebottombearings.
►Fig.9:
1. Lower holder 2. Upper holder 3.Bottombearing
5. Withpressingthemiddlepartofthebandsaw
blade,positionthebladearoundonewheel.Movingthe
wheeltoAsidemakesiteasiertodoso.
►Fig.10: 1. Wheel 2.Rubbertire
6.
Positionthebandsawbladeontheotherwheelsimilarly.
7.
Positiontheedgeofthebandsawbladeonrubbertire.
8. Holdthebandsawbladeinplaceandturnthe
bladetighteninglevercounterclockwiseuntilitstops.
Thisplacespropertensiononthebandsawblade.
9. Close the wheel cover.
NOTICE: Make sure that the band saw blade is
correctly positioned around the wheels.
NOTICE: Start and stop the tool two or three
times to make sure that the band saw blade runs
properly on the wheels.
Toremovethebandsawblade,followtheinstallation
procedure in reverse.

Содержание

Скачать