Bosch GGS 18 V-LI Solo 0.601.9B5.303 [15/211] Operation

English | 15

Bosch Power Tools 1 609 92A 0MA | (10.7.14)

To remove the battery 7, press the battery unlocking button 6

and pull the battery upward out of the power tool. Do not ex-

ert any force.

Battery Charge-control Indication (see figure A)

The three green LEDs of the battery charge-control indicator

10 indicate the charge condition of the battery 7. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

Press button 9 to indicate the charge condition. This is also

possible when the battery 7 is removed.

When no LED lights up after pushing button 9, then the bat-

tery is defective and must be replaced.

Mounting the Grinding Tools (see figure B)

 Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Only use properly fitting and undamaged open-end

spanners (see “Technical Data”).

– Clean the grinder spindle 3 and all parts to be mounted.

– Hold the grinder spindle 3 with open-end spanner 11 by

the spanner flats.

Loosen the clamping nut 2 with open-end spanner 12 by

applying it to the spanner flats and turning in anticlockwise

direction.

– Insert the clamping shaft of the grinding tool to the stop in-

to the collet chuck 1.

– Hold the grinder spindle 3 firmly with open-end spanner

11 and clamp the tool bit with open-end spanner 12 by the

spanner flats, turning in clockwise direction.

The grinding tools must run completely concentrical. Do not

continue to use out-of-round grinding accessories, instead,

replace before continuing to work.

 Do not tighten the collet chuck of the clamping nut as

long as no grinding accessory is mounted. Otherwise,

the collet chuck can become damaged.

 Only use grinding points with a matching shank diame-

ter. A grinding point/accessory with a shank diameter that

does not fit the tool holder (see “Technical Data”), can not

be clamped properly and will damage the collet chuck.

 The application tool must be clamped at least 10 mm.

The inner shank dimension L

can be used to calculate the

maximum permitted speed of the application tool from the

specifications provided by manufacturer of the application

tool. It must not be less than the maximum speed of the

power tool.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium-ion batteries with the

voltage listed on the nameplate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

Insert the charged battery 7 into the base of the power tool

until the battery is securely locked.

Switching On and Off

To start the power tool, push the On/Off switch 5 forwards.

To lock the On/Off switch 5, press the On/Off switch 5 down

at the front until it latches.

To switch off the power tool, release the On/Off switch 5 or,

if it is locked, briefly push down the back of the On/Off switch

5 and then release it.

To save energy, only switch the power tool on when using it.

Restarting Protection

The restarting protection feature prevents uncontrolled re-

starting of the machine after an interruption in the power sup-

ply.

To restart the operation, switch the On/Off switch 5 to the

Off position and start the machine again.

Note: When switching off and on again very quickly, it is pos-

sible that the restarting protection is triggered; this will pre-

vent the power tool from starting, although the On/Off switch

5 is actuated. Set the On/Off switch 5 to the off position, and

then switch the power tool on again.

Working Advice

Optimum grinding results are achieved when the grinding tool

is moved uniformly back and forth with light pressure. Pres-

sure that is too strong reduces the performance capability of

the machine and causes the grinding tool to wear more quick-

ly.

 Protect the abrasive wheels from impacts.

LED Capacity

Continuous lighting 3 x green

≥ 2/3

Continuous lighting 2 x green

≥ 1/3

Continuous lighting 1 x green

<1/3

Flashing light 1 x green

Reserve

OBJ_BUCH-1461-003.book Page 15 Thursday, July 10, 2014 10:26 AM

Bosch GGS 18 V-LI Solo 0.601.9B5.303 [15/211] Operation

Содержание

Похожие устройства