Makita 18В, BL, XPT, Li-ion, 140 Нм DTD157Z [7/68] Electric brake

7 ENGLISH

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydi󰀨erslightly

fromtheactualcapacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

thebatteryprotectionsystemworks.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutso󰀨powertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placed under one of the following conditions:

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automaticallyandthelampblinks.Inthissituation,let

thetool/batterycoolbeforeturningthetoolonagain.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically.Inthiscase,removethebatteryfromthe

toolandchargethebattery.

Switch action

►Fig.3: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ing the switch trigger for about 6 minutes.

Electric brake

This tool is equipped with an electric brake. If the tool

consistentlyfailstoquicklystopaftertheswitchtrigger

is released, have the tool serviced at a Makita service

center.

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.4: 1. Lamp

►Fig.5: 1. Button

Pulltheswitchtriggertoturnonthelamp.Toturno󰀨,

releaseit.Thelampgoesoutapproximately10seconds

after releasing the switch trigger.

Tokeepthelampo󰀨,turno󰀨thelampstatus.Firstpull

and release the switch trigger. And then press the but-

ton

for one second within 10 seconds.

To turn on the lamp status again, press the button again

similarly.

NOTE:Toconrmthelampstatus,pullthetrigger.

Whenthelamplightsupbypullingtheswitchtrigger,

the lamp status is ON. When the lamp does not come

on, the lamp status is OFF.

NOTE:Whenthetoolisoverheated,thelightashes

foroneminute,andthentheLEDdisplaygoeso󰀨.In

this case, cool down the tool before operating again.

NOTE:Useadryclothtowipethedirto󰀨thelensof

the lamp. Be careful not to scratch the lens of lamp, or

itmaylowertheillumination.

Reversing switch action

►Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

directionofrotationbeforethetoolstopsmaydam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Makita 18В, BL, XPT, Li-ion, 140 Нм DTD157Z [7/68] Electric brake

Содержание

Похожие устройства