Woods Airmaster WOZ 400, 116м3/ч, выработка озона 400 мг/ч WOZ400 Инструкция по эксплуатации ENG онлайн [12/72] 868597

Woods Airmaster WOZ 400, 116м3/ч, выработка озона 400 мг/ч WOZ400 Инструкция по эксплуатации ENG онлайн [12/72] 868597

GB

12

Operating Instructions

Use

Position the ozone device in a dry

place that is ventilated well, ideally

high up and approx. 1.5 m above the

oor. It is important to ensure that

nothing prevents the air entering the

fan.

Connect the mains cable supplied to

the mains socket (A4).

The ozone device can now be started

by pressing the on-o button (A3).

The ozone device starts in operating

mode, with full power (100%).

It can take up to about 5 minutes to

achieve the full eect.

Starting the machine

1. Start the ozone device.

Press the switch (A3) to ON

2. Switch o the ozone device

Press the power switch (A3) to OFF

Digital control with timer

(Applicable to Wood’s Airmaster

WOZ500/2000/4000)

The ozone quantity/output can be

varied between 0 and 100%.

Timer modes: daily, interval and

shut-o timer.

See “Digital control” instructions on

the next page for further information.

Using the silicone hose

The nipple and silicone hose

accessory (E1) is mounted in the

connecting nut (B1) and the ozone

can be directed into the space to be

treated such as car interiors, partition

walls and water treatment.

Connecting to a ventilation duct

When connecting to a ventilation

duct/spiral pipe, the ventilation

nozzle (E5) is connected by means of

a nut rivet. The ozone device is then

connected with the hose nipple and

silicone hose (E1).

Maintenance

NOTE!

Always unplug the device before

carrying out servicing/maintenance.

Replacing the prelter

The prelter has to be replaced every

two to four months, depending on

the ambient environment.

1. Undo the lter holder (A2) by

hand.

2. Replace the lter with a new one.

3. Put back the lter holder (A2).

Replacing the ozone pipe

Ozone is formed when a high-voltage

power supply is passed into the

ozone pipe. The ozone pipe must be

replaced if the ozone concentration

declines or ceases entirely.

A. If your ozone device has four

chassis screws per long side:

1. Undo the eight screws on the long

sides of the chassis.

2. Lift the cover o the machine.

3. Go to point C.

B. If your ozone device has no

visible chassis screws:

1. Undo the two screws that hold the

handle in place.

2. Turn the machine upside down.

3. Undo the four screws that hold the

machine’s feet in place.

4. Remove the chassis cover by

pulling/pushing the cover forwards.

5. Go to point C.

C. Replace the ozone pipe:

1. Carefully remove the two air hoses

from the ozone pipe (F4).

2. Undo the two cables between the

high-voltage module (F3) and the

ozone pipe (F4).

3. The screws that hold the ozone

pipe in position (F4) are undone

from the underside.

4. Assemble in reverse order.

NOTE: The ozone pipe and prelter

are wear parts and are not covered by

the warranty.

All servicing other than that

described here must be performed

by the manufacturer or an authorised

partner.

Servicing

You must contact your local dealer

if your ozone device requires

maintenance. Receipts must be

presented for all warranty claims.

Storage instructions

Store your ozone device at room

temperature between +1 °C and

+35°C.

USING AND MAINTAINING YOUR OZONE DEVICE

It is important to replace the

prelter at regular intervals

and to replace the ozone pipe

regularly. Failing to do this may

impair the capacity of the ozone

device and possibly harm the

device.

Похожие устройства