Главная
Skipped breadcrumb items
KBH 25-2 U
Инструкция Страница: 15

Главная
Fein
KBH 25-2 U
Инструкция Страница: 15

Fein KBH 25-2 U — безопасные методы работы с электроинструментами и пылью [15/117]

Превью страниц Страница 15 / 117

Fein KBH 25-2 U [15/117] Handling hazardous dusts

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Handling hazardous dusts

For work procedures with this power tool where mate-

rial is removed, dusts develop that can be hazardous to

one’s health.

Contact with or inhaling some dust types, e. g. asbestos

and asbestos-containing materials, lead-containing coat-

ings, metal, some wood types, minerals, silicate particles

from materials containing stone, paint solvents, wood

preservatives, antifouling paints for vessels, can trigger

allergic reactions to the operator or bystanders and/or

lead to respiratory infections, cancer, birth defects or

other reproductive harm. The risk from inhaling dusts

depends on the exposition. Use dust extraction matched

appropriately for the developing dust, as well as personal

protective equipment and provide for good ventilation of

the workplace. Leave the processing of asbestos-contain-

ing materials to specialists.

Wood and light-metal dust, hot mixtures of sanding dust

and chemical materials can self-ignite under unfavourable

conditions or cause an explosion. Avoid sparking in the

direction of the dust collector as well as overheating of

the power tool and the materials being sanded, empty the

dust collector/container in time, observe the material

manufacturer’s working instructions, as well as the rele-

vant regulations in your country for the materials being

worked.

Operating instructions.

Adjust the Rotation selector switch only when the

machine is at a complete stop.

When the power supply is disconnected while the motor

is running or when the switched-on power tool is

plugged in, the motor will not restart.

When the application tool continuously blocks or is sub-

ject to overload, the motor stops automatically. Restart

the motor again.

Insert the pilot bit with a turning motion into the tool

holder until it springs back.

Carry out core-drilling processes without interruption, if

possible. To complete a started and interrupted drilling

run, repeat the center-drilling process.

Replace dull pilot bits; they may not be reground.

Remove the chippings and the drilled core after each

drilling process.

Chippings are sharp and hot!

When changing a drill bit, pay attention not to damage

the cutting edges.

When core drilling layered material, remove the core and

the chippings after drilling each layer.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power tool.

The total insulation of the power tool can be impaired.

Blow out the interior of the power tool via the ventila-

tion slots frequently with dry and oil-free compressed air,

and connect a residual current device (RCD) on the line

side.

If the supply cord of this power tool is damaged, it must

be replaced by a specially prepared cord available through

the FEIN customer service centre.

If required, you can change the following parts yourself:

Auxiliary handle, application tools

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your power tool may include only

a part of the accessories described or shown in this

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

Technical documents at: C. & E. FEIN GmbH, EGZ,

D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should

be sorted for environmental-friendly recycling.

CAUTION

OBJ_BUCH-0000000027-002.book Page 15 Thursday, July 21, 2011 9:04 AM

Fein KBH 25-2 U — безопасные методы работы с электроинструментами и пылью [15/117]

Содержание

Похожие устройства