Suzuki GSX-R600 (2006) Инструкция по эксплуатации онлайн [10/517] 114712
![Suzuki GSX-R600 (2006) Инструкция по эксплуатации онлайн [10/517] 114712](/views2/1121283/page10/bga.png)
GENERAL INFORMATION 1-3
* If parts replacement is necessary, replace the parts with Suzuki Genuine Parts or their equiva-
lent.
* When removing parts that are to be reused, keep them arranged in an orderly manner so that
they may be reinstalled in the proper order and orientation.
* Be sure to use special tools when instructed.
* Make sure that all parts used in reassembly are clean. Lubricate them when specified.
* Use the specified lubricant, bond, or sealant.
* When removing the battery, disconnect the negative cable first and then the positive cable.
* When reconnecting the battery, connect the positive cable first and then the negative cable,
and replace the terminal cover on the positive terminal.
* When performing service to electrical parts, if the service procedures do not require use of
battery power, disconnect the negative cable from the battery.
* When tightening the cylinder head or case bolts and nuts, tighten the larger sizes first.
Always tighten the bolts and nuts diagonally from the inside toward outside and to the speci-
fied tightening torque.
* Whenever you remove oil seals, gaskets, packing, O-rings, locking washers, self-locking
nuts, cotter pins, circlips and certain other parts as specified, be sure to replace them with
new ones. Also, before installing these new parts, be sure to remove any left over material
from the mating surfaces.
* Never reuse a circlip. When installing a new circlip, take care not to expand the end gap larger
than required to slip the circlip over the shaft. After installing a circlip, always ensure that it is
completely seated in its groove and securely fitted.
* Use a torque wrench to tighten fasteners to the specified torque. Wipe off grease and oil if a
thread is smeared with them.
* After reassembling, check parts for tightness and proper operation.
* To protect the environment, do not unlawfully dispose of used motor oil, engine coolant and
other fluids: batteries and tires.
* To protect Earth’s natural resources, properly dispose of used motorcycle and parts.
Содержание
- 35100 01e gsx r600 service manual 1
- Chassis 2
- Cooling and lubrication system 2
- Electrical system 2
- Emission control information 2
- Engine 2
- Exhaust system 2
- Fi system diagnosis 2
- Foreword 2
- Foreword_group index 2
- Fuel system and throttle body 2
- General information 2
- Group index 2
- Periodic maintenance 2
- Servicing information 2
- Wiring diagram 2
- Component parts and work to be done 3
- How to use this manual 3
- To locate what you are looking for 3
- Symbol 4
- Abbreviations used in this manual 5
- Wire color 7
- Contents 8
- Country and area codes 8
- General information 8
- General precautions 9
- Warning caution note 9
- Left side 11
- Right side 11
- Serial number location 11
- Suzuki gsx r600k6 06 model 11
- Brake fluid 12
- Engine oil for other countries 12
- Engine oil for usa 12
- Fuel for other countries 12
- Fuel for usa and canada 12
- Fuel oil and engine coolant recommendation 12
- Anti freeze engine coolant 13
- Engine coolant 13
- Front fork oil 13
- Liquid amount of water engine coolant 13
- Water for mixing 13
- Break in procedures 14
- Cylinder identification 14
- Information labels 15
- Dimensions and dry mass 16
- Drive train 16
- Engine 16
- Specifications 16
- Capacities 17
- Chassis 17
- Electrical 17
- Contents 18
- Periodic maintenance 18
- Periodic maintenance chart 19
- Periodic maintenance schedule 19
- Lubrication points 20
- Note before lubricating each part clean off any rusty spots and wipe off any grease oil dirt or grime lubricate exposed parts which are subject to rust with a rust preventative spray whenever the motorcycle has been operated under wet or rainy conditions 20
- Periodic maintenance 2 3 20
- Proper lubrication is important for smooth operation and long life of each working part of the motorcycle major lubrication points are indicated below 20
- Air cleaner 21
- Maintenance and tune up procedures 21
- Spark plug 22
- Valve clearance 24
- 10 periodic maintenance 27
- How to use this chart i measure valve clearance engine is cold ii measure present shim size iii match clearance in vertical column with present shim size in horizontal column example valve clearance is 0 3 mm present shim size 1 0 mm shim size to be used 1 0 mm 27
- Intake side 27
- Tappet shim selection table intake tappet shim no 12892 05c00 xxx 27
- Tappet shim set 12800 05830 27
- Exhaust side 28
- How to use this chart i measure valve clearance engine is cold ii measure present shim size iii match clearance in vertical column with present shim size in horizontal column example valve clearance is 0 3 mm present shim size 1 0 mm shim size to be used 1 0 mm 28
- Periodic maintenance 2 11 28
- Tappet shim selection table exhaust tappet shim no 12892 05c00 xxx 28
- Tappet shim set 12800 05830 28
- Engine oil and oil filter 29
- Exhaust control valve 30
- Engine idle speed 31
- Fuel line 31
- Evaporative emission control system e 33 only 32
- Pair air supply system 32
- Throttle cable play 32
- Throttle valve synchronization 32
- Clutch 33
- Cooling system 34
- Drive chain 37
- Steering 44
- Front fork 45
- Rear suspension 45
- Exhaust pipe bolt and nut 46
- Chassis bolts and nuts 47
- Compression pressure check 49
- Compression test procedure 49
- Oil pressure check 50
- Sample data sampled from cold starting through warm up 51
- Sds check 51
- Data at 3 000 r min under no load 52
- Data at the time of racing 52
- Periodic maintenance 2 35 52
- 36 periodic maintenance 53
- Data of intake negative pressure during idling 100 c 53
- Data of secondary throttle valve operation at the time of starting 53
- Contents 54
- Engine 54
- Engine components removable with engine in place 55
- Engine removal 56
- Engine removal and installation 56
- Engine installation 63
- Engine disassembly 67
- Cmp sensor 79
- Cylinder head cover 79
- Engine components inspection and service 79
- Pair reed valve 79
- Crankcase breather reed valve 80
- Pcv hose 80
- Camshaft 81
- Cam chain guide 83
- Cam chain tension adjuster 83
- Cam chain tensioner 83
- Cylinder head and valve 83
- Clutch 91
- Clutch lifter 92
- Clutch sleeve hub primary driven gear assembly 92
- Do not attempt to disassemble the oil pump assembly 94
- Oil pump 94
- Starter clutch 94
- Gearshift system 96
- Generator 96
- Water pump 96
- Oil pressure regulator 97
- Oil strainer 97
- Transmission 98
- Cylinder 101
- Piston and piston ring 102
- Crankcase 104
- Crankshaft and conrod 114
- Crankshaft journal bearing 118
- Crankshaft thrust bearing 121
- Engine reassembly 123
- M 2 kgf m 19 lb ft 129
- M 2 kgf m 19 lb ft m8 initial 15 n m 1 kgf m 11 lb ft final 26 129
- M8 initial 15 n m 1 kgf m 11 lb ft final 26 129
- Replace the bolts with new precoated ones for plate 131
- Crankcase breather cover bolt 10 n m 1 kgf m 7 lb ft 132
- Gear position switch bolt 7 n m 0 kgf m 5 lb ft 132
- 96 engine 149
- Contents 152
- Fi system diagnosis 152
- Contents 153
- Fi system diagnosis 153
- Electrical parts 154
- Precautions in servicing 154
- Ecm various sensors 155
- Electrical circuit inspection procedure 157
- Using the multi circuit tester 160
- 10 fi system diagnosis 161
- Fi system technical features 161
- Injection time injection volume 161
- The factors to determine the injection time include the basic fuel injection time which is calculated on the basis of intake air pressure engine speed and throttle opening angle and various compensations these compensations are determined according to the signals from various sensors that detect the engine and driving conditions 161
- Compensation of injection time volume 162
- Injection stop control 162
- Fi system parts location 163
- 14 fi system diagnosis 165
- Fi system wiring diagram 165
- Ecm couplers 166
- Ecm terminal 166
- Ecm couplers 167
- Self diagnosis function 168
- User mode 168
- Dealer mode 169
- Tps adjustment 171
- Fail safe function 172
- Cold warm always 174
- Customer complaint analysis 174
- Example customer problem inspection form 174
- Fi system troubleshooting 174
- Hesitation on acceleration no initial combustion 174
- High low r min 174
- Malfunction display code lcd user mode no display malfunction display dealer mode no code malfunction code 174
- Malfunction indicator lamp condition led always on sometimes on always off good condition 174
- No combustion lack of power poor starting at 174
- Other other 174
- Other other engine rpm jumps briefly other 174
- Others others 174
- Poor idling poor idling engine stall when poor fast idle immediately after start abnormal idling speed 174
- Problem symptoms difficult starting poor driveability 174
- Record details of the problem failure complaint and how it occurred as described by the customer for this purpose use of such an inspection form such as below will facilitate collecting information required for proper analysis and diagnosis 174
- Surging surging abnormal knocking 174
- Throttle valve is opened throttle valve is opened throttle valve is closed 174
- Unstable unstable load is applied hunting r min to r min other 174
- User name model vin date of issue date reg date of problem mileage 174
- Visual inspection 175
- Self diagnosis reset procedure 176
- Self diagnostic procedures 176
- Use of sds diagnostic procedures 177
- Use of sds diagnosis reset proce dure 178
- Show data when trouble displaing data at the time of dtc 179
- Malfunction code and defective condition 180
- C11 p0340 cmp sensor circuit malfunction 184
- C12 p0335 ckp sensor circuit malfunction 186
- C13 p0105 h l iap sensor circuit malfunction 189
- Iaps lead wire continuity continuit 191
- Iap sensor output voltage approx 2 v at idle speed 192
- Iaps lead wire continuity 192
- C14 p0120 h l tp sensor circuit malfunction 195
- Tps lead wire continuity 197
- C15 p0115 h l ect sensor circuit malfunction 200
- Ects lead wire continuity 201
- C21 p0110 h l iat sensor circuit malfunction 204
- Iats lead wire continuity 205
- At 20 c 68 f terminal terminal 207
- Iat sensor resistance approx 2 5 207
- C22 p1450 h l ap sensor circuit malfunction 208
- Aps lead wire continuity 210
- Aps lead wire continuity 211
- C23 p1651 h l to sensor circuit malfunction 214
- Tos lead wire continuity 215
- Tos lead wire continuity 216
- C24 p0351 c25 p0352 c26 p0353 or c27 p0354 ignition system malfunction 217
- C28 p1655 stv actuator circuit malfunction 218
- Termina 219
- C29 p1654 h l stp sensor circuit malfunction 221
- Stps lead wire continuity 222
- Stps lead wire continuity 223
- C31 p0705 gp switch circuit malfunction 226
- C32 p0201 c33 p0202 c34 p0203 or c35 p0204 primary fuel injector circuit malfunction 228
- C36 p1764 c37 p1765 c38 p1766 or c39 p1767 secondary fuel injector circuit malfunction 231
- C41 p0230 h l fp relay circuit malfunction 234
- C42 p01650 ig switch circuit malfunction 237
- C44 p0130 p0135 ho2 sensor ho2s circuit malfunction for e 02 19 238
- Ho2s lead wire continuity 239
- C46 p1657 h l or p1658 excv actuator circuit malfunction 242
- Excva lead wire continuity 243
- Excva lead wire continuity 244
- At 20 30 c 68 86 f terminal terminal 251
- C49 p1656 pair control solenoid valve circuit malfunction 251
- Pair valve resistance 18 22 251
- C60 p0480 cooling fan relay circuit malfunction 254
- Ckp sensor inspection 256
- Ckp sensor removal and installation 256
- Cmp sensor inspection 256
- Cmp sensor removal and installation 256
- Iap sensor inspection 256
- Iap sensor removal and installation 256
- Sensors 256
- Tp sensor inspection 256
- Tp sensor removal and installation 256
- Tps adjustment 256
- Ap sensor inspection 257
- Ap sensor removal and installation 257
- Ect sensor inspection 257
- Ect sensor removal and installation 257
- Iat sensor inspection 257
- Iat sensor removal and installation 257
- Stp sensor inspection stp sensor removal and installation 257
- To sensor inspection to sensor removal and installation 257
- Ho2 sensor inspection for e 02 19 258
- Ho2 sensor removal and installation 258
- Stp sensor adjustment 258
- Contents 259
- Fuel system and throttle body 259
- Fuel delivery system 260
- Fuel system 261
- Fuel tank lift up 261
- Fuel pressure inspection 262
- Fuel tank installation 262
- Fuel tank removal 262
- Fuel pump inspection 263
- Fuel discharge amount inspection 264
- Fuel pump relay inspection 265
- Fuel pump and fuel filter removal 266
- Fuel mesh filter inspection and cleaning 268
- Fuel pump and fuel mesh filter installation 268
- Construction 271
- Throttle body 271
- Air cleaner box removal and instal lation 272
- Throttle body removal 273
- Throttle body disassembly 274
- Inspection 276
- Throttle body cleaning 276
- Throttle body reassembly 277
- Tp sensor mounting screw 3 n m 0 5 kgf m 2 lb ft 277
- Throttle body installation 279
- Stp sensor adjustment 280
- Fuel injector inspection 281
- Fuel injector installation 281
- Fuel injector removal 281
- Fast idle 282
- Fast idle adjustment 282
- Throttle valve synchronization 284
- Throttle position sensor tps setting 285
- Contents 286
- Exhaust system 286
- Exhaust control system 287
- Exhaust system 287
- Full close full open 288
- Operation 288
- Excva exhaust control valve actuator and excv exhaust control valve 289
- Excva removal 289
- Excva installation 290
- Excva pulley inspection 290
- Excva inspection 291
- Excv cable replacement 292
- Excva adjustment 293
- Excv exhaust pipe muffler removal 295
- Excv exhaust pipe muffler installation 297
- Excv inspection 297
- Do not use the adjustable wrench to turn excva pul 299
- Ley so as not to cause damage to the internal gear of 299
- Position 299
- Slots of excva pulley must be located to adjustment 299
- When adjusting the no 1 and no 2 cables the cable 299
- Contents 300
- Cooling and lubrication system 300
- 2 cooling and lubrication system 301
- 30 c 24 f 55 40 c 44 f 60 55 c 67 f 301
- Anti freeze 1 350 ml 2 2 us lmp pt water 1 350 ml 2 2 us lmp pt 301
- Anti freeze density freezing point 301
- At the time of manufacture the cooling system is filled with a 50 50 mixture of distilled water and ethylene glycol anti freeze this 50 50 mixture will provide the optimum corrosion protection and excellent heat pro tection and will protect the cooling system from freezing at temperatures above 31 c 24 f if the motorcycle is to be exposed to temperatures below 31 c 24 f this mixing ratio should be increased up to 55 or 60 according to the figure 301
- Engine coolant 301
- Engine coolant including reserve tank capacity 301
- Use a high quality ethylene glycol base anti freeze mixed with distilled water do not mix an alcohol base anti freeze and different brands of anti freeze do not put in 60 and more anti freeze or 50 and less refer to below figure do not use a radiator anti leak additive 301
- You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot after the engine cools wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off the engine must be cool before servicing the cooling system coolant is harmful if it comes in contact with skin or eyes flush with water if swallowed accidentally induce vomiting and call physician immediately keep it away from children 301
- Cooling circuit 302
- Cooling circuit inspection 302
- Oil cooler 302
- Radiator and water hoses 303
- Radiator cap inspection 303
- Radiator inspection and cleaning 303
- Radiator removal 303
- Radiator installation 304
- Water hose inspection 304
- Cooling fan 305
- Inspection 305
- Installation 305
- Removal 305
- Cooling fan relay inspection 306
- Ect sensor 306
- Inspection 306
- Removal 306
- 1 kgf m 13 lb ft 307
- Installation 307
- Take special care when handling the ect sensor it may cause damage if it gets a sharp impact 307
- Inspection 308
- Removal 308
- Thermostat 308
- Installation 309
- Removal and disassembly 310
- Water pump 310
- Inspection 312
- Reassembly and installation 313
- Lubrication system 316
- Oil cooler 316
- Oil filter 317
- Oil jet 317
- Oil pressure 317
- Oil pressure regulator 317
- Oil pressure switch 317
- Oil pump 317
- Oil strainer 317
- Crankshaft crankshaft crankshaft 318
- Engine lubrication system chart 318
- Main gallery 318
- Oil pan 318
- Sub gallery 1 318
- Sub gallery 2 318
- Engine lubrication system 319
- Chassis 321
- Contents 321
- Chassis 322
- Contents 322
- Exterior parts 323
- Fastener removal and installation 323
- Body cowling cover and lower bracket cover 325
- Inner under cowling 325
- Under cowling 325
- Body cowling 326
- Screen 326
- Air intake pipe 327
- Cowling brace 327
- Front seat 327
- Fuel tank lower side cover 327
- Frame cover 328
- Rear seat seat tail cover 328
- Construction 329
- Front wheel 329
- Removal and disassembly 330
- Inspection 332
- 99000 25010 suzuki super grease a or equivalent grease 333
- Chassis 8 13 333
- Reassemble and install the front wheel in the reverse order of removal and disassembly pay attention to the following points 333
- Reassembly and installation 333
- Wheel bearing apply suzuki super grease a to the wheel bearings 333
- Construction 337
- Front fork 337
- Removal and disassembly 338
- Inspection 341
- Reassembly 342
- Installation 346
- Suspension setting 347
- Construction 348
- Steering damper 348
- Inspection 349
- Installation 349
- Removal 349
- Construction 350
- Steering 350
- Removal 351
- Inspection and disassembly 352
- Installation 353
- Reassembly 353
- Steering tension adjustment 355
- Construction 356
- Handlebars 356
- Removal 356
- Installation 357
- Construction 360
- Rear wheel 360
- Removal 361
- Inspection and disassembly 362
- 44 chassis 364
- Reassemble and install the rear wheel in the reverse order of removal and disassembly pay attention to the following points 364
- Reassembly and installation 364
- Construction 368
- Rear shock absorber 368
- Removal 369
- Do not attempt to disassemble the rear shock absorber 371
- Inspection 371
- Rear shock absorber scrapping procedure 371
- Installation 372
- Suspension setting 373
- Construction 374
- Rear suspension 374
- Removal 375
- Inspection 376
- Disassembly 379
- 60 chassis 380
- Reassemble and install the swingarm in the reverse order of disassembly and removal pay attention to the following points 380
- Reassembly and installation 380
- Final inspection and adjustment 383
- Shock absorber cushion lever and cushion rod mounting bolt nut 383
- Construction 384
- Front brake 384
- Brake pad replacement 385
- Brake fluid replacement 386
- Caliper disassembly 387
- Caliper removal 387
- Caliper inspection 388
- Caliper reassembly 388
- Caliper installation 389
- Brake disc inspection 390
- Master cylinder removal and disassembly 391
- Master cylinder inspection 392
- Master cylinder reassembly 393
- Master cylinder installation 394
- Construction 395
- Rear brake 395
- Brake pad replacement 396
- Brake fluid replacement 397
- Caliper removal and disassembly 397
- Caliper inspection 399
- Caliper reassembly 400
- Caliper installation 401
- Master cylinder removal and disassembly 401
- Master cylinder inspection 403
- Master cylinder reassembly 403
- Master cylinder installation 404
- Inspection 405
- Tire and wheel 405
- Tire removal 405
- Valve inspection 406
- Tire installation 407
- Balancer weight installation 408
- Drive chain 409
- Drive chain cutting 409
- Drive chain connecting 410
- Contents 413
- Electrical system 413
- Contents 414
- Electrical system 414
- Cautions in servicing 415
- Connector 415
- Coupler 415
- Battery 416
- Connecting the battery 416
- Semi conductor equipped part 416
- Wiring procedure 416
- Using the multi circuit tester 417
- Location of electrical components 418
- Charging system 420
- Troubleshooting 420
- Inspection 421
- 12 electrical system 424
- Make sure that the fuses are not blown and the battery is fully charged before diagnosing 424
- Starter motor will not run step 1 1 shift the transmission to neutral 2 pull the clutch lever turn on the ignition switch with the engine stop switch in the run position and lis ten for a click from the starter relay when the starter button is pushed is a click sound heard 424
- Starter system and side stand ignition interlock system 424
- Step 2 1 check if the starter motor runs when its terminal is connected to the battery terminal do not use thin wire because a large amount of current flows does the starter motor run 424
- Troubleshooting 424
- Yes faulty starter relay loose or disconnected starter motor lead wire loose or disconnected between starter relay and battery terminal no faulty starter motor 424
- Yes go to step 2 no go to step 3 424
- Starter motor removal 425
- Starter motor disassembly 426
- Starter motor inspection 426
- Starter motor reassembly 427
- Starter relay inspection 428
- Side stand ignition interlock system parts inspection 429
- Blue black white 430
- Off except neutral 430
- On neutral 430
- 20 electrical system 432
- E 03 24 33 the circuit cuts off the ignition primary current for all spark plugs 432
- Ignition system 432
- Note the fuel cut off circuit is incorporated in this ecm in order to prevent over running of engine when engine speed reaches 15 500 r min this circuit cuts off fuel at the fuel injector but under no load the clutch lever is pulled or the gear position is neutral this circuit cuts off fuel when engine speed reaches 15 100 r min 432
- Under no load the engine can run over 15 100 r min though the ignition cut off circuit is effec tive which may possibly cause engine damage do not run the engine without load over 15 100 r min at anytime 432
- Description the immobilizer an anti theft system is installed as a standard equipment the immobilizer verifies that the key id agrees with ecm id by means of radio communication through the immobilizer antenna when the id agreement is verified the system makes the engine ready to start 433
- Electrical system 9 21 433
- Immobilizer except for e 03 28 33 433
- Troubleshooting 435
- Inspection 437
- Orange blue green white 439
- Combination meter 441
- Description 441
- Removal and disassembly 442
- Inspection 443
- Push reset 443
- Release 443
- Sec 5 sec 443
- Time ignition switch adjuster switch push 443
- Headlight brake light taillight license plate light and turn signal light 447
- Cooling fan relay 449
- Fuel pump relay 449
- Relays 449
- Starter relay 449
- Turn signal side stand relay 449
- Ignition switch installation 450
- Ignition switch removal 450
- Switches inspection 451
- Battery 452
- Initial charging 452
- Specifications 452
- Recharging operation 454
- Servicing 454
- Contents 455
- Servicing information 455
- Fi system malfunction code and defective condition 456
- Troubleshooting 456
- Engine 460
- Radiator cooling system 466
- Chassis 467
- Brakes 468
- Electrical 469
- Battery 470
- Wiring harness cable and hose routing 471
- Wiring harness routing 471
- Battery lead wire 1 fix the clamp in parallel with the cover surface 2 white tape 473
- Servicing information 10 19 473
- Ho2 sensor harness routing for e 02 19 474
- Cable routing 475
- Fuel tank hose routing 476
- Cooling system hose routing 477
- 1 clamp should face downward 5 after positioning the clamp with stopper tighten the clamp bolt 478
- 2 clamp should face backward 6 insert the clamp to the hole of the front fender fully 478
- 24 servicing information 478
- 3 after the brake hose union has contacted the stopper tighten the union bolt 7 the green paint is right side and face upside 478
- Brake hose guide 4 clamp the brake hose firmly 478
- Front brake hose routing 478
- Rear brake hose 2 pass the reservoir hose above the brake hose 2 brake fluid reservoir hose 3 position the brake union with the stopper before tightening 3 stopper 4 face the clamp end inside 4 rear lower fender 5 white marking 1 face the clamp end backward 6 insert the reservoir hose into the hose connector to the root 479
- Rear brake hose routing 479
- Servicing information 10 25 479
- Fuel tank installation 480
- Cowling installation 481
- Servicing information 10 27 481
- Rear fender installation 483
- Side stand installation 484
- Under cowling cushion rubber heat shield installation 484
- Front footrest installation 485
- Rear view mirror installation 486
- Special tools 487
- Engine 491
- Tightening torque 491
- Cooling system 492
- Fi system and intake air system 492
- Chassis 493
- Tightening torque chart 494
- Camshaft cylinder head 495
- Service data 495
- Valve valve guide 495
- Cylinder piston piston ring 496
- Conrod crankshaft 497
- Oil pump 497
- Clutch 498
- Transmission drive chain 498
- Injector fuel pump fuel pressure regulator 499
- Thermostat radiator fan coolant 499
- Fi sensors 500
- Electrical 501
- Throttle body 501
- Brake wheel 502
- Wattage 502
- Fuel oil 504
- Suspension 504
- Contents 505
- Emission control information 505
- Emission control systems 506
- Fuel injection system 506
- Crankcase emission control system 507
- Exhaust emission control system pair system 508
- Noise emission control system 509
- Pair air supply system and emission control system inspection 510
- Pair hoses 510
- Pair reed valve 510
- Pcv hose 510
- Pair control solenoid valve 511
- 8 emission control information 512
- Pair air supply system hose routing 512
- Pair control solenoid valve 1 white marking 2 pair reed valve 2 yellow marking opposite side 512
- Ho2 sensor inspection for e 02 19 513
- 2 3 4 5 6 514
- A 10 a 10 a 10 a 15 a 15 a 514
- Ap sensor 514
- Brake light switch 514
- Ckp sensor 514
- Clutch switch 514
- Cmp sensor gp switch 514
- Cooling fan motor 514
- Cooling fan relay 514
- Dimmer switch 514
- E 02 19 24 514
- Ect sensor 514
- Engine stop switch starter button front brake switch 514
- For e 02 19 514
- Generator 514
- Hazard switch 514
- Head hi 2 head lo 3 fuel 4 ignition 5 signal 6 fan 514
- Ho2 sensor 514
- Horn button 514
- Iat sensor 514
- Pair control solenoid 514
- Passing light switch 514
- Primary injector 1 primary injector 2 514
- Primary injector 3 primary injector 4 514
- Regulator rectifier 514
- Secondary injector 1 secondary injector 2 514
- Secondary injector 3 secondary injector 4 514
- Speedometer 514
- To sensor 514
- Tp sensor 514
- Turn signal light switch 514
- Wiring diagram 514
- Wiring diagrams wire color refer to section wire color 514
- A 10 a 10 a 10 a 15 a 15 a 515
- Ap sensor 515
- Battery 515
- Brake light switch 515
- Ckp sensor 515
- Clutch switch 515
- Cooling fan motor 515
- Dimmer switch 515
- E 03 28 33 515
- Ect sensor 515
- Engine stop switch starter button front brake switch 515
- Front turn signal light l 515
- Front turn signal light r 515
- Fuel pump 515
- Fuel pump relay 515
- Fuse box 515
- Handlebar switch l 515
- Handlebar switch r 515
- Hazard switch 515
- Head hi 2 head lo 3 fuel 4 ignition 5 signal 6 fan 515
- Headlight hi 515
- Headlight lo 515
- Horn button 515
- Iat sensor 515
- Ignition coil 1 515
- Ignition coil 2 515
- Ignition coil 3 515
- Ignition coil 4 515
- License plate light 515
- Oil pressure switch 515
- Passing light switch 515
- Position light l 515
- Position light r 515
- Primary injector 1 primary injector 2 515
- Primary injector 3 primary injector 4 515
- Rear turn signal light l 515
- Rear turn signal light r 515
- Secondary injector 1 secondary injector 2 515
- Secondary injector 3 secondary injector 4 515
- Side stand switch 515
- Starter motor 515
- Starter relay 515
- T turn signal indicator light b hi beam indicator light n neutral indicator light f fuel warnning light oil oil indicator light 515
- To sensor 515
- Tp sensor 515
- Turn signal light switch 515
Похожие устройства
- Efco PR 40 S Инструкция по эксплуатации
- Efco MZ 2050RX Инструкция по эксплуатации
- Suzuki GSX-R600 (1996-2000) Инструкция по эксплуатации
- Efco MZ 2060 Инструкция по эксплуатации
- Suzuki GSX-R1100 (1993-1998) Инструкция по эксплуатации
- Efco MZ 2080RK Инструкция по эксплуатации
- Suzuki GSX-R1100 (1989-1992) Инструкция по эксплуатации
- Efco MZ 2090X Инструкция по эксплуатации
- Suzuki GSX-R1100 (1986-1988) Инструкция по эксплуатации
- Efco MZ 2090R GC Инструкция по эксплуатации
- Suzuki GSX-R750 (2004) Инструкция по эксплуатации
- Efco MZ 2030 Инструкция по эксплуатации
- Suzuki GSX-R750 (1993-1995) Инструкция по эксплуатации
- Efco IP 1450 S Инструкция по эксплуатации
- Suzuki GSX-R600 (2004) Инструкция по эксплуатации
- Efco IP 1200 S Инструкция по эксплуатации
- Suzuki GSX-R600 (2001-2002) Инструкция по эксплуатации
- Efco IP 1350 S Инструкция по эксплуатации
- Suzuki GSX1400 (2002) Инструкция по эксплуатации
- Efco IP 3000 HS Инструкция по эксплуатации
Скачать
Случайные обсуждения