Home
Главная
Kramer
Интерфейсы для Витой Пары
TP-185
Руководства по эксплуатации Страница: 20

Kramer TP-185 Руководства по эксплуатации онлайн [20/21] 139815

Содержание

Kramer electronics ltd 1
User manual 1
Tables 3
Getting started 4
Introduction 4
Getting started 5
Quick start 5
This quick start chart summarizes the basic setup and operation steps 5
Overview 6
Shielded twisted pair unshielded twisted pair 6
Defining the tp 185 8 channel uxga audio rs 232 to cat 5 transmitter 7
Defining the tp 185 8 channel uxga audio rs 232 to cat 5 transmitter 8
Table 1 tp 185 front and rear panel features 8
Installing the tp 185 in a rack 9
Connecting and configuring the tp 185 10
Connecting the tp 185 10
Connecting to the tp 185 via an rs 232 connection 11
Connecting to the tp 185 via an rs 485 connection 11
Connecting multiple tp 185 units via the rs 485 bus 12
Enabling and disabling the reply feature 13
Setting the dip switches on the tp 185 13
Setting the rs 485 bus termination 13
Dip switches 2 3 and 4 set either the reply source in hardware mode table 2 or machine number in software mode table 3 14
Figure 6 tp 185 reply source or machine number dip switches 14
Note when there is more than one tp 185 attached to the rs 485 bus only one unit can have a reply path set 14
Setting the dip switches on the tp 185 14
Setting the reply source or machine number 14
Table 2 hardware mode reply source dip switch setting 14
Table 3 software mode rs 485 machine number dip switch setting 14
When dip switch 1 is up reply is disabled default down on reply is enabled 14
When there is more than one tp 185 attached to the rs 485 bus each unit must have a unique machine number 14
Dip switch 8 sets the operating mode to either hardware or software mode 15
Dip switches 5 6 and 7 set the serial port baud rate in both hardware and software modes according to table 4 note in a multiple device configuration all devices must be set to the same baud rate 15
Figure 7 tp 185 baud rate dip switches 15
Figure 8 tp 185 baud rate hardware software dip switch 15
Hardware mode 15
In hardware mode the rs 232 data is passed from any input to all outputs tp 185 routes the reply from the output port defined by the dip switches 2 3 and 4 see section 7 for reliable operation only one port can be defined 15
Selecting hardware software mode 15
Setting the dip switches on the tp 185 15
Setting the rs 232 rs 485 baud rate dip switches 15
Table 4 serial port baud rate dip switch setting 15
When the dip switch is off the unit is set to hardware mode default on the unit is set to software mode 15
Software mode 16
Wiring the twisted pair rj 45 connectors 16
Default communication parameters 17
Lists the tp 185 default communication parameters 17
Of the tp 185 17
Table 6 technical specification 17
Table 7 17
Table 7 tp 185 communication parameters 17
Technical specifications 17
Technical specifications of the tp 185 are shown in table 6 17
Default communication parameters 18
Desti desti nation 18
Instruction 18
Kramer communication protocol 2000 18
Machine number 18
Msb lsb 18
Output 18
Table 8 protocol command definition 18
The rs 232 rs 485 protocol 2000 uses four bytes of information as shown in table 8 the data rate is set by the dip switches see table 4 with no parity 8 data bits and 1 stop bit 18
Command description reply 19
Default communication parameters 19
Description input output 19
Instruction definition for specific instruction note 19
Note all values in the table are hexadecimal unless otherwise stated notes on table 9 note 1 when the pc sends this command if the instruction is valid the unit replies by sending the pc the same 4 bytes that it was sent except for the first byte where the destination bit is set high note 2 if o6 0 tx this command defines reads the definition of the output 1 2 or3 to pass the rs 232 direct command from any input in this case the instruction does not modify previously set output numbers allowing the setting of multiple outputs for the direct command if o6 1 rx the command defines reads the definition of the output 1 2 or 3 to pass the reply from the output to inputs in this case the instruction resets a previously set output number preventing the setting of multiple outputs for the reply note 3 the reply to this command is as follows the same command and output codes as were sent are returned and the input is assigned the value of the parameter that was read the reply is per the definit 19
Table 10 sample tp 185 control commands 19
Table 9 instruction codes for the tp 185 19
Caution 21
For the latest information on our products and a list of kramer distributors visit 21
Where updates to this user manual may be found we welcome your questions comments and feedback 21

Kramer TP-185 Руководства по эксплуатации онлайн [20/21] 139815

Содержание

Похожие устройства