Ardo COF 2110 SAX [10/44] Установка

Содержание

INVERSIONS MANIGUA VERTICALE RIMOZIONE DELLE PROTEZIONI PER IL TRASPORTO Se il voslro apparecchio e dolalo della maniglia verticale maníala ma dea dele di cambiare la parle di apertura bisognerà procederé all inversione anche della mani glia verticale nel seguenle modo Rimuovere la protezione dalla guarnizione della porta fig ó La protezione evita i possibili danni della guarnizione dovuti al trasporto La protezione deve essere rimossa per poter chiuaere ermeticamente la porta Per togliere la protezione tira re leggermente un estremita ruotandola verso l estemo Rimuovere i dispositivi di blocco dei ripani invetro Tali element in plástico evitare lo spostamento dei ripani durante il trasporto Per rimuovere i dispositivi di blocco procederé come segue a Aff er ra regli elementi in plástico ruotandoli fino a disimpegnarli totalmentedal rip ano b Estrarre gli element tirandoli verso l esterno Smontare la maniglia tramite le due viti di sostegno Estrarre tramite leggera pressione i t a ppi salvaforo che troverete nel lato opposto della porta Rotare la maniglia di 180 e riposizionare le due viti quindi rinfilare i ta ppi salvaforo sul lato opposto POSITIONING AND INSTALLATION MOVING THE VERTICAL HANDLE REMOVING THE TRAN PORT PROTECTIONS Remove the door seal protection fig 6 The protection prevents possible damage to the seal during transport The protection must be removed in order to be able to If your appliance is filled with a vertical handle and you wart Io change the opening direction the position of the vertical handle must also be changed following the proce dure reported below Remove the handle by unscrewing the fixing screws dose and seal the door lb remove the protection pul I one end gently while notating it outwards Q Remove the glass shelf locking devices These plastic devices prevent the shelves from moving during transport To remove the devices proceed as follows Remove the hole plugs on the opposite side of the door by pressing lightly a Grip the plastic element and rotate it until it is free of the shelf b Extract the elements by pulling outwards Rotate the handle 180 and refit it using the two screws Insert the plugs in the holes left on the opposite side УСТАНОВКА ПЕРЕСТАНОВКА ВЕРТИКАЛЬНОЙ РУЧКИ Е ели на дверце Вашего холодильника морозильника установлена вертикальная ручка но Вы хотите поменять направление открывания дверцы то перестановка ручки осуществляется следующим образом Ф Q Q УДАЛЕНИЕ ЗАЩИТНЫХ ДЕТАЛЕЙ ДЛЯ ТРАНСПОРТИРОВКИ ф Снимите защитную пленку препятствует повреждению чтобы дверца холодильника снять Потяните за конец ее вверх Отвинтите два крепежных винта и отсоедините ручку с изоляции дверцы см рис Защитная пленка изоляции при транспортировке Для того плотно закрывалась защитную пленку нужно защитной пленки одновременно поворачивая Снимите крепежные детали стеклянных полок Эти пластиковые детали препятствуют перемещению полок во время транспортировки Крепежные детали снимают следующим образом а Возьмитесь за п ласгнювую часть детали и поверните ее так чтобы она отделилась от попки б Снимите крепежные детали нажимая по направлению вверх Снимите крышки закрывающие отверстия для ручки на противоположной стороне дверцы слегка нажимая на них Поверните ручку на 180 и прикрепите ручку винтами на новом месте Установите крышки на отверстия где раньше была установлена ручка 599