Supermicro X8DTI-F — руководство пользователя для материнских плат X8DT3 и X8DTi [12/99]

Содержание

• User s manual p.1
• Manual revision 1 c p.2
• Printed in the united states of america p.2
• Warning handling of lead solder materials used in this product may expose you to lead a chemical known to the state of california to cause birth defects and other reproductive harm p.2
• Release date march 9 2012 p.2
• About this manual p.3
• Preface p.3
• Manual organization p.3
• About this motherboard p.3
• Conventions used in the manual p.4
• Headquarters p.5
• Europe p.5
• Contacting supermicro p.5
• Asia pacific p.5
• Chapter 1 introduction p.6
• Table of contents p.6
• Preface p.6
• Chapter 2 installation p.6
• Chapter 3 troubleshooting p.7
• Chapter 4 bios p.8
• Appendix b software installation instructions p.8
• Appendix a bios error beep codes p.8
• Checklist p.9
• Introduction p.9
• Chapter 1 p.9
• 1 overview p.9
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f layout x8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f layout p.11
• I button optional no optional no optional no p.11
• X8dt3 i series p.11
• X8dt3 f ln4f only for sas raid configuration refer to the lsi user guide posted on our website http www supermicro com support manuals p.11
• Sata ich10r yes yes yes yes yes yes p.11
• Sas connectors jumpers and the lsi 1068e chip are available on the p.11
• Sas 1068e yes no yes no yes no p.11
• Only ipmi dedicated lan is for x8dt3 i f x8dt3 i ln4f only p.11
• Lan3 lan4 jpl2 jumper no no no no yes yes p.11
• Lan port 3 lan port 4 and lan controller 2 are for the x8dt3 i ln4f p.11
• Ipmi 2 w kvm no no yes yes yes yes p.11
• Ipmi 2 and the dedicated lan w kvm support are available on the p.11
• Differences between the models p.11
• Chapter 1 introduction p.11
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f p.11
• X8dt3 i f ln4f only for more information please refer to the user guide posted on our website http www supermicro com support manuals p.11
• When le1 is on the onboard power connection is on make sure to unplug p.12
• To the system p.12
• To avoid possible system overheating be sure to provide adequate airflow p.12
• The power cables before removing or installing components p.12
• Posted on our website http www supermicro com support manuals p.12
• Platform module header the 5600 series processors and 1 5v dimm modules are supported by the rev 2 0 or later version motherboard p.12
• Motherboard layout p.12
• Mation on the onboard components p.12
• Jumpers not indicated are for test purposes only p.12
• Jpb bmc enable jumper jwf1 dom pwr connector tpm trusted p.12
• Indicates the location of pin 1 also refer to chapter 2 for detailed infor p.12
• For ipmi configuration please refer to the winbond bmc user s guide p.12
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.12
• X8dt3 i series p.12
• Note to provide adequate power to the system be sure to connect jpw1 jpw2 and jpw3 to the power supply refer to the warning on p 1 12 for more information p.13
• Chapter 1 introduction p.13
• Pc health monitoring p.14
• Motherboard features p.14
• Memory p.14
• Expansion slots p.14
• Chipset p.14
• Onboard i o p.15
• Dimensions p.15
• Cd diskette utilities p.15
• Acpi features p.15
• Pci e x16 p.16
• Note this is a general block diagram please see the previous mother board features pages for details on the features of each motherboard p.16
• Block diagram of the 5520 platform p.16
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.16
• Pci e x8 p.16
• Pci e x4 p.16
• Main features of the 5500 5600 series processor and the 5520 chipset p.17
• 3 chipset overview p.17
• System resource alert p.18
• Recovery from ac power loss p.18
• Fan status monitor with firmware control p.18
• Environmental temperature control p.18
• 5 pc health monitoring p.18
• 4 special features p.18
• Wake on lan wol p.19
• Slow blinking led for suspend state indicator p.19
• Main switch override mechanism p.19
• 6 acpi features p.19
• 7 power supply p.20
• 8 super i o p.20
• X8dt3 i f x8dt3 i ln4f only p.21
• 9 overview of the winbond wpcm450 controller for p.21
• Unpacking p.23
• Precautions p.23
• Installation p.23
• Chapter 2 p.23
• 1 static sensitive devices p.23
• Tools needed p.24
• Installation instructions p.24
• 2 motherboard installation p.24
• 3 processor and heatsink installation p.25
• Installing a cpu heatsink p.27
• Removing the heatsink p.28
• Caution p.29
• 4 memory installation p.29
• Dimm installation p.29
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.30
• The x8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f supports up to 192 gb registered ecc ddr3 or up to 48 gb unbuffered ecc non ecc 1333 mhz 1066 mhz 800 mhz in 12 dimms please note that memory speed support depends on the type of cpu used in the motherboard p.30
• Rdimm population for the motherboard w 5500 processors installed p.30
• Memory support p.30
• Memory population for optimal performance for a motherboard with two cpus installed p.30
• Memory population for optimal performance p.30
• For the motherboards w 5500 series processors installed p.30
• For memory to work properly follow the tables below for memory installation p.30
• For a motherboard with one cpu cpu2 installed p.30
• For a motherboard with one cpu cpu1 installed p.30
• Dimmmodulepopulationconfiguration p.30
• Cpu1 cpu2 p.30
• Branch 0 branch 1 branch 2 p.30
• Memory support for the motherboards w 5600 processors installed p.31
• Chapter 2 installation p.31
• V udimm population for the motherboard w 5600 processors installed p.31
• V rdimm population for the motherboard w 5600 processors installed p.31
• V dimms p.31
• Udimm population for the motherboard w 5500 processors installed p.31
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.32
• V udimm population for the motherboard w 5600 processors installed p.32
• V rdimm population for the motherboard w 5600 processors installed p.32
• V dimms p.32
• Note 2 due to memory allocation to system devices the amount of memory that remains available for operational use will be reduced when 4 gb of ram is used the reduction in memory availability is dispropor tional see the following memory availability table p.32
• Note 1 due to os limitations some operating systems may not show more than 4 gb of memory p.32
• Chapter 2 installation p.33
• 5 control panel connectors io ports p.34
• Backpaneli oportlocationsanddefinitions p.34
• Back panel connectors io ports p.34
• Back panel connectors p.34
• Atx ps 2 keyboard and ps 2 mouse ports p.35
• The atx ps 2 keyboard and ps 2 mouse are located next to the back panel usb ports 0 1 on the moth erboard see the table at right for pin definitions p.35
• Mouse green p.35
• Keyboard purple p.35
• Keyboard p.35
• Chapter 2 installation p.35
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.36
• Universal serial bus usb p.36
• Two universal serial bus ports usb 0 and usb 1 are located on the i o p.36
• Front panel usb 6 7 p.36
• Front panel usb 4 5 p.36
• Front panel usb 3 p.36
• Front panel usb 2 p.36
• Backpanel usb 1 p.36
• Backpanel usb 0 p.36
• Back panel additionally six usb con nections usb 2 3 4 5 6 7 on the motherboard to provide front chassis access cables are not included see the tables on the right for pin definitions p.36
• Video connector p.37
• A video vga connector is located next to com port1 on the io back plane this connector is used to provide video display refer to the board layout below for the location p.37
• Two com connections com1 com2 are located on the motherboard com1 is located on the backplane io panel com2 is located next to the onboard battery to provide additional onboard serial connection support see the table on the right for pin definitions p.37
• Serial ports p.37
• Chapter 2 installation p.37
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.38
• Two ethernet ports lan 1 lan2 are located at on the io backplane in addition lan 3 lan4 are supported on the x8dt3 i ln4f a dedicated lan is also located on the x8dt3 i f x8dt3 i ln4f to provide kvm sup port for ipmi 2 all these ports ac cept rj45 type cables note please refer to the led indicator section for lan led information p.38
• Nc no connection p.38
• Lan5 x8dt3 i f ln4f p.38
• Lan4 x8dt3 i ln4f only p.38
• Lan3 x8dt3 i ln4f only p.38
• Ethernet ports p.38
• Jf1 header pins p.39
• Jf1 contains header pins for various buttons and indicators that are normally lo cated on a control panel at the front of the chassis these connectors are designed specifically for use with supermicro server chassis see the figure below for the descriptions of the various control panel buttons and led indicators refer to the following section for descriptions and pin definitions p.39
• Front control panel p.39
• Chapter 2 installation p.39
• Frontcontrolpanelpindefinitions p.40
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.42
• The power fail led connection is located on pins 5 and 6 of jf1 re fer to the table on the right for pin definitions p.42
• Power fail led p.42
• Overheat oh fan fail led p.42
• Connect an led cable to the oh fan fail connection on pins 7 and 8 of jf1 to provide advanced warnings of chassis overheating or fan failure refer to the table on the right for pin definitions p.42
• The reset button connection is located on pins 3 and 4 of jf1 attach it to a hardware reset switch on the computer case refer to the table on the right for pin definitions p.43
• The power button connection is located on pins 1 and 2 of jf1 momentarily con tacting both pins will power on off the sys tem this button can also be configured to function as a suspend button with a setting in the bios see chapter 4 to turn off the power when set to suspend mode press the button for at least 4 seconds refer to the table on the right for pin definitions p.43
• Reset button p.43
• Power button p.43
• Chapter 2 installation p.43
• X8dt3 i series p.44
• 6 connecting cables p.44
• Chassis intrusion p.45
• X8dt3 i series p.45
• C fan 3 p.45
• Tachometer p.45
• B fan 2 p.45
• Pwr modulation p.45
• A fan 1 p.45
• Pindefinitions jl1 p.45
• Pindefinitions p.45
• Pin definition p.45
• Intrusion input p.45
• I chassis intrusion p.45
• H fan 8 cpu1 fan p.45
• Ground p.45
• G fan 7 cpu2 fan p.45
• Fan header p.45
• F fan 6 p.45
• E fan 5 p.45
• D fan 4 p.45
• Internal speaker p.46
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.46
• The internal speaker located at sp1 can be used to provide audible indica tions for various beep codes see the table on the right for pin definitions refer to the layout below for the loca tions of the internal buzzer sp1 p.46
• Power led speaker p.46
• On the jd1 header pins 1 3 are used for power led indication and pins 4 7 are for the speaker see the table on the right for speaker pin definitions please note that the speaker con nector pins 4 7 are for use with an external speaker if you wish to use the onboard speaker you should close pins 6 7 with a jumper p.46
• Wake on lan p.47
• The wake on lan header is located at jwol on the motherboard you must also have a lan card with a wake on lan connector and a cable to use this feature see the table on the right for pin definitions p.47
• The joh1 header is used to connect an led indicator to provide warnings of chassis overheating or fan failure this led will blink when a fan failure occurs refer to the table on right for pin definitions p.47
• Overheat led fan fail joh1 p.47
• Chapter 2 installation p.47
• Power system management bus p.49
• Power smb p.49
• Chapter 2 installation p.49
• C connector j6 monitors power supply fan and system temperatures see the table on the right for pin definitions p.49
• C connector p.49
• C connection on your system p.49
• A system management bus header for the ipmi slot is located at j5 connect the appropriate cable here to use the ipmb p.49
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.50
• Tpm header p.50
• Note this header is avail able on a r 2 0 or later version of motherboard p.50
• Dom power connector p.50
• A trusted platform module header jtpm1 is located next to com2 port to provide tpm support for system data security see the table on the right for pin definitions p.50
• A power connector for sata dom disk_on_module devices is located at jwf1 connect the appropriate cable here to provide power support for your dom devices p.50
• X8dt3 i series p.51
• Explanation of jumpers p.51
• 7 jumper settings p.51
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.52
• Watch dog jwd is a system monitor that can reboot the system when a software ap plication hangs close pins 1 2 to reset the system if an application hangs close pins 2 3 to generate a non maskable interrupt signal for the application that hangs see the table on the right for jumper settings watch dog must also be enabled in the bios p.52
• Watch dog enable disable p.52
• Note for an atx power supply you must completely shut down the sys tem remove the ac power cord and then short jbt1 to clear cmos p.52
• Jbt1 is used to clear cmos instead of pins this jumper consists of contact pads to prevent the accidental clearing of cmos to clear cmos use a metal object such as a small screwdriver to touch both pads at the same time to short the connection always remove the ac power cord from the system before clear ing cmos p.52
• Cmos clear p.52
• Jumper jps1 allows you to enable or disable the onboard sas connections the default setting is pins 1 2 to enable the connection see the table on the right for jumper settings p.54
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.54
• Sas raid select x8dt3 x8dt3 f x8dt3 ln4f only p.54
• Sas raid config select p.54
• Sas enable disable x8dt3 x8dt3 f x8dt3 ln4f only p.54
• Sas enable p.54
• Note for more information on lsi sas raid configuration please refer to the lsi megaraid user s guide posted on our website http www supermicro com support manuals p.54
• Jumper jps2 allows you to select raid configuration settings for the onboard sas connections see the table on the right for jumper settings p.54
• Note this header is available on a r 2 0 or later version of motherboard p.55
• Jumper jpb allows you to enable or disable embedded the wpcm 450 bmc controller baseboard manage ment controller to support ipmi 2 o on thex8dt3 i f ln4f the default set ting is open to enable the connection see the table on the right for jumper settings p.55
• Chapter 2 installation p.55
• Bmc enable p.55
• Color status definition p.56
• Amber 1 gbps p.56
• Activity right amber blinking active p.56
• Activity led right p.56
• 8 onboard led indicators p.56
• Yellow flashing active p.56
• X8dt3 i series p.56
• Off no connection or 10 mbps p.56
• Link left green solid 100 mbps p.56
• Led state p.56
• Led color definition p.56
• Lan 1 lan 2 link led right p.56
• Lan 1 lan 2 activity led left p.56
• Ipmi lan link led left p.56
• Green 100 mbps p.56
• X8dt3 x8dti x8dt3 f x8dti f x8dt3 ln4f x8dti ln4f user s manual p.58
• Onboard power led p.58
• An onboard power led is located at le1 on the motherboard when this led is lit the system is on be sure to turn off the system and unplug the power cord before removing or installing components see the tables at right for more information p.58
• A onboard power led p.58
• 9 floppy drive serial ata and sas connections p.59
• A i sata0 p.60
• X8dt3 i series p.60
• Serial ata p.60
• Pindefinitions p.60
• Pin definition p.60
• H sas 4 7 x8dt3 f ln4f p.60
• Ground p.60
• G sas 0 3 x8dt3 f ln4f p.60
• F i sata5 p.60
• E i sata4 p.60
• D i sata3 p.60
• C i sata2 p.60
• B i sata1 p.60
• No power p.61
• Chapter 3 p.61
• Before power on p.61
• 1 troubleshooting procedures p.61
• Troubleshooting p.61
• No video p.61
• Memory errors p.62
• Losingthesystem ssetupconfiguration p.62
• 2 technical support procedures p.62
• 3 frequently asked questions p.63
• Warnin p.64
• 4 returning merchandise for service p.64
• Starting bios setup utility p.65
• Chapter 4 p.65
• 1 introduction p.65
• Starting the setup utility p.66
• Howtochangetheconfigurationdata p.66
• 2 main setup p.66
• Boot features p.68
• 3 advancedsetupconfigurations p.68
• Powerconfiguration p.69
• Processor and clock options p.70
• Cpubridgeconfiguration p.72
• Advanced chipset control p.72
• Northbridgeconfiguration p.73
• Southbridgeconfiguration p.74
• Ide sataconfiguration p.75
• Select 0 4 to allow the ami bios to use pio mode 0 4 it has a data transfer rate of 3 mb s 16 mb s see the table below p.77
• S m a r t for hard disk drives p.77
• Pio mode select options p.77
• Option selected pio mode max transfer rate p.77
• Option selected dma mode max transfer rate p.77
• Dma mode select options p.77
• Dma mode p.77
• Chapter 4 ami bios p.77
• Bit data transfer p.77
• Self monitoring analysis and reporting technology smart can help predict impending drive failures select auto to allow the ami bios to automatically de tect hard disk drive support select disabled to prevent the ami bios from using the s m a r t select enabled to allow the ami bios to use the s m a r t to support hard drive disk the options are disabled enabled and auto p.77
• Select enable to support 32 bit ide data transfer the options are enabled and disabled p.77
• Select auto to allow the bios to automatically detect ide dma mode when the ide disk drive support cannot be determined the options are auto swdman mwdman and udman see the table below for dma mode select options p.77
• Select auto to allow the ami bios to automatically detect the pio mode use this value if the ide disk drive support cannot be determined p.77
• Pci pnpconfiguration p.78
• Superiodeviceconfiguration p.79
• Remoteaccessconfiguration p.80
• Hardware health p.81
• Configuration p.81
• Acpiconfiguration p.83
• Ipmiconfiguration p.84
• View bmc system event log p.85
• Setlanconfiguration p.85
• Macaddressconfiguration p.86
• Ipaddressconfiguration p.86
• Gateway address p.87
• Subnetmaskconfiguration p.87
• Eventlogconfiguration p.88
• 4 security settings p.88
• Usb drives p.90
• Removable drives p.90
• Hard disk drives p.90
• Cd dvd drives p.90
• Boot device priority p.90
• 5 bootconfiguration p.90
• Other drives p.91
• Network drives p.91
• 6 exit options p.91
• A 1 bios error beep codes p.93
• Bios error beep codes p.93
• Appendix a p.93
• Appendix b p.95
• Software installation instructions p.95
• B 1 installing software programs p.95
• B 2 configuringsuperodoctoriii p.96