![CONEL SPECTRE v3 ERT [20/39] Router design](/icons/site-icon-64.png){kind=icon}
CONEL SPECTRE v3 ERT [20/39] Router design
Превью страниц
Страница 20 /
39
![CONEL SPECTRE v3 ERT [20/39] Router design](/views2/1190476/page20/bg14.png)
5. ROUTER DESIGN
5.8.3 Antenna connector WiFi
If the router is equipped with WiFi module on the customer’s request, appropriate antenna
is connected to the reverse SMA connector (WiFi).
The extarnal antenna is connected by screwing this antenna to the reverse SMA connector
on the front panel of the router (see figure below).
Figure 13: Antenna connector
13
Содержание
93- Spectre v3 ert
- International headquarters
- Headquarters
- European headquarters
- Used symbols
- Gpl license
- Contents
- Contents
- List of figures
- List of tables
- Safety instruction
- Please observe the following instructions
- Product disposal instructions
- Router description
- Contents of package
- Router design
- Figure 5
- Figure 4
- Figure 3
- Figure 2
- Version switch plastic
- Version switch metal
- Version switch and wifi plastic
- Version switch and wifi metal
- Table 1 router versions
- Spectre v3 ert router is supplied in the following versions see table below all ver sions are available in plastic or metal box according to customer requirements all versions are available with poe pd power over ethernet powered device so you can power the router from both eth0 and eth1 interfaces or with poe pse power source equipment so you can power other devices by the router
- Router versions
- Router design
- Ordering codes
- Delivery identification
- Delivery identification
- Table 5 type of router box
- Router design
- Letter z type of connector on the power supply
- Letter y type of router box
- Examples of complete order code
- Router design
- Mechanical dimensions and mounting recommendations
- Basic dimensions of router box
- Router design
- Removing from the din rail
- Router design
- Description of the rear panel
- Description of the front panel
- Table 9 status indication
- Status indication
- Router design
- Additionaly it can indicate a device without poe support connected on the other side of the cable in this case the indication is caused by low impedance lesser than 500 ω of this device without poe support you can solve this by disabling the poe pse feature on the proper eth port in the router s web interface see configuration manual for v3 routers 2
- About router status inform nine led indicators on the front panel each eth port has two additional leds that provide information about port status
- Router design
- Power connector pwr
- Antenna connector wifi
- Router design
- Router design
- Microsd card reader
- Router design
- Ethernet ports eth0 and eth1
- Router design
- Power over ethernet poe
- Usb port
- Router design
- Router design
- I o port
- Router design
- Router design
- Switch interface
- Router design
- Interfaces description
- First use
- Connecting the router before first use
- Connecting the router before first use
- First use
- Configuration over web browser
- Configuration
- Configuration over web browser
- Configuration
- First use
- Technical parameters
- Basic parameters
- Type tests and environmental conditions
- Technical parameters
- Technical parameters of wifi
- Technical parameters of i o port
- Technical parameters
- Technical parameters of power over ethernet poe
- Technical parameters
- Other technical parameters
- Recommended literature
- Troubleshooting
- Troubleshooting
- Www conel com
- Customers support
- Customer support for nam
Похожие устройства
-
CONEL CGU 04iИнструкция по эксплуатации -
CONEL CDX 800Инструкция по эксплуатации -
CONEL CDA 70Технические характеристики -
CONEL CDA 70Инструкция по эксплуатации -
CONEL XR5i v2EРуководство по конфигурации -
CONEL XR5i v2EТехнические характеристики -
CONEL XR5i v2EРуководство по подключению -
CONEL XR5i v2EИнструкция по эксплуатации
-
CONEL XR5i v2FТехнические характеристики
-
CONEL XR5i v2FРуководство по конфигурации
-
CONEL XR5i v2FИнструкция по эксплуатации
-
CONEL CR10 v2Руководство по подключению
