M-Audio Omni i/o Инструкция по эксплуатации онлайн [12/30] 19296
![M-Audio Omni i/o Инструкция по эксплуатации онлайн [12/30] 19296](/views2/1020435/page12/bgc.png)
NOTE: The Aux Ins add some gain to the signal into the Omni mixer
so that the aux levels blend more easily with the audio tracks
coming from your computer. 17dB of gain is given to the Aux In
signals.
5. Connect the “Record (Mix) Outs” of the Omni to the analog inputs of your
mixdown deck, such as a cassette tape deck or a DAT. If your mixdown
deck’s inputs are unbalanced, use cable with a 1/4” Tip-Sleeve plug on the
Omni Record Outs, with the appropriate plug, such as 1/4” TS, RCA, etc.,
into the mixdown deck inputs.
If your mixdown deck’s inputs are balanced, use a cable with a 1/4” Tip-
Ring-Sleeve plug on the Omni Record (Mix) Outs, with the appropriate plug,
such as 1/4” TRS, XLR, etc., into the mixdown deck inputs.
6. To connect an effects unit to the Omni I/O, use a 1/4” TS plug if your effects
unit accepts only an unbalanced signal, or a 1/4” TRS plug if your effects
unit accepts balanced signals. Connect your cable from the “FX Send” jack to
the mono input of your effects unit.
You may take the stereo output of your effects unit, and plug into the L&R
“Effects Return.” Once again, use TS for unbalanced and TRS for balanced
operation. If your effect unit has only a mono output, you may plug that mono
output into the Omni FX Return left input only, and that mono signal will
appear panned in the center of the stereo soundfield. Otherwise, left and right
signals will be panned hard left and hard right, respectively.
An effects return is an auxiliary input to a mixer. You can also return effects to
the Aux Ins of the Omni. If you have a mono MIDI instrument, you may want to
use the left input of the effects return to handle this mono signal, and return the
effect (if stereo) to the Aux In.
NOTE: The Effects Return adds some gain to the signal into the
Omni mixer, so that the return levels blend more easily with the
audio tracks coming from your computer. 10dB of gain is given to
the Effects Return signals.
7. With the Omni “Monitor Level” control in the leftmost position (volume off),
press the power switch and power up the Omni. Next, power up your
computer. With the volume down on your monitoring system, power up
your monitoring system.
You are now setup to monitor and mix recorded audio tracks from your
computer via the Delta card, to add effects to the audio tracks, and to sequence
and mix in your MIDI keyboards. If your music program has a demo file with
audio and MIDI tracks, launch the program and open the file. Make sure that the
MIDI ports are set correctly.
12
Содержание
- Table of contents 1
- Introduction 2
- Theory of operation 2
- Features 3
- Front rear and top panel descriptions 4
- What s in the box 4
- Operational basics definitions 7
- Basic playback setup for the omni i o 11
- Basic recording setup for the omni i o 14
- Inputs 15
- Outboard gear 15
- Omni signal flow chart 16
- Sequencing and the omni i o 17
- Below for your convenience we ve created a chart describing what source you should select within your music software for your respective omni inputs next you ll want to set up the way you monitor the signals you are recording then set up the gain structure for your recording levels 19
- Having read the basic recording setup in section 7 of this manual you understand that omni mic instr channel 1 is connected to the delta h w hardware in1 omni mic instr channel 2 is connected to the delta h w hardware in 2 and omni line ins 3 4 are connected to delta h w ins 3 4 respectively this is the omni recording section and these are the record channels 19
- Recording audio to the delta 44 or 66 19
- Recording software will vary but once you ve set up your levels recording them is fairly basic recording is also covered extensively in your delta manual and there should also be a tutorial in your software s manual 19
- Take some time to read the delta manual that came with your delta card recording audio tracks requires a proper record setup but setup for monitoring those signals while recording is equally important 19
- With the gain controls on the omni turned down plug a microphone or an instrument such as electric or acoustic guitar into mic instr channel 1 and or channel 2 or plug a line level device such as a cd player or additional mic instrument pre amps into line ins 3 4 19
- Mixing with the omni 26
- Alternate omni setups 28
- Limited lifetime warranty 30
Похожие устройства
- Panasonic HDC-TM80EE-K Инструкция по эксплуатации
- Ariston Bravo M 7023 U-PV1 Инструкция по эксплуатации
- HP Pavilion p6621ru XS463EA Инструкция по эксплуатации
- Scarlett SC-219 Инструкция по эксплуатации
- Loewe Spheros R 32 HD+ Инструкция по эксплуатации
- Panasonic PT-DZ570E Инструкция по эксплуатации
- Polaris Stream Pro 5.3 Инструкция по эксплуатации
- JVC GZ-HM30B Инструкция по эксплуатации
- HP Pavilion Elite E410ru XJ004EA Инструкция по эксплуатации
- Scarlett SC-218 Инструкция по эксплуатации
- Loewe Spheros R 42 Инструкция по эксплуатации
- Panasonic PT-DW530E Инструкция по эксплуатации
- JVC GZ-HM446B Инструкция по эксплуатации
- HP Pavilion p6700ru LF969EA Инструкция по эксплуатации
- Loewe Viewvision DR+ Инструкция по эксплуатации
- Panasonic PT-DX500E Инструкция по эксплуатации
- Scarlett SC-217 Инструкция по эксплуатации
- HP Pavilion E-550ruLL444EA Инструкция по эксплуатации
- JVC GZ-HM446 Инструкция по эксплуатации
- Loewe Xelos A 20 Инструкция по эксплуатации