M-Audio Omni i/o [11/30] Basic playback setup for the omni i o
![M-Audio Omni i/o [11/30] Basic playback setup for the omni i o](/views2/1020435/page11/bgb.png)
6. Basic Playback Setup for the Omni I/O
This section will get you setup for playback and monitoring, as well as for
mixing down when your project is complete (though you may make changes in
your setup at that time). A discussion of the Omni components becomes more
detailed in sections 9 through 11.
Install your Delta card first, according to the Delta installation procedure found
in the Delta 44 or 66 manual. In the step by step instructions that follow, the
items in quotations such as “9v AC Power Jack” relate specifically to numbered
items on the front and back panels of the Omni I/O.
1. Make sure that the host computer is powered off. Using the shielded 15 pin
to 15 pin cable that came with your Delta card, connect one end of the cable
to the D-sub connector on the Delta card, and the other end to the “15 Pin D-
sub Connector” on the back of the Omni I/O.
This cable is a shielded audio cable, and connects the Omni to the four
analog inputs on the Delta card (H/W Inputs 1 through 4). The 15 pin to 15
pin cable also connects the Delta H/W Outs 1 through 4 to the Omni mixer,
and also to the “Omni Direct Outs 1-4.”
2. Plug the 9v AC power supply into the wall outlet, and connect the 2.5 mm
plug into the “9v AC Power Jack” on the back of the Omni.
3. Connect the “Monitor Outs” of the Omni to the inputs of your monitoring
system. If your monitoring system’s inputs are unbalanced, use a cable with
a 1/4” Tip-Sleeve plug on the Omni monitor outs, with the appropriate plug,
such as 1/4” TS, RCA, etc., into the monitoring system inputs.
If your monitoring system’s inputs are balanced, use a cable with a 1/4” Tip-
Ring-Sleeve plug on the Omni monitor outs, with the appropriate plug, such as
1/4” TRS, XLR, etc., into the monitoring system inputs.
NOTE: A mixer such as the Omni is in itself a pre-amp. This means
that you can connect the Monitor Outs to a power amp or directly
to powered speakers. You can also connect the Monitor Outs to an
integrated amplifier such as a home stereo (though you may not
need as much level from the Omni Monitor Control).
4. Plug the audio outputs from your MIDI keyboards, sound modules, and
drum machines into each of the four Omni stereo “Aux Ins.” Use a cable that
is a single 1/4” TRS plug to two 1/4” TS plugs, (sometimes referred to as an
“insert cable”), or cabling that is similar while appropriate to your MIDI
modules outputs.
11
Содержание
- Table of contents 1
- Introduction 2
- Theory of operation 2
- Features 3
- Front rear and top panel descriptions 4
- What s in the box 4
- Operational basics definitions 7
- Basic playback setup for the omni i o 11
- Basic recording setup for the omni i o 14
- Inputs 15
- Outboard gear 15
- Omni signal flow chart 16
- Sequencing and the omni i o 17
- Below for your convenience we ve created a chart describing what source you should select within your music software for your respective omni inputs next you ll want to set up the way you monitor the signals you are recording then set up the gain structure for your recording levels 19
- Having read the basic recording setup in section 7 of this manual you understand that omni mic instr channel 1 is connected to the delta h w hardware in1 omni mic instr channel 2 is connected to the delta h w hardware in 2 and omni line ins 3 4 are connected to delta h w ins 3 4 respectively this is the omni recording section and these are the record channels 19
- Recording audio to the delta 44 or 66 19
- Recording software will vary but once you ve set up your levels recording them is fairly basic recording is also covered extensively in your delta manual and there should also be a tutorial in your software s manual 19
- Take some time to read the delta manual that came with your delta card recording audio tracks requires a proper record setup but setup for monitoring those signals while recording is equally important 19
- With the gain controls on the omni turned down plug a microphone or an instrument such as electric or acoustic guitar into mic instr channel 1 and or channel 2 or plug a line level device such as a cd player or additional mic instrument pre amps into line ins 3 4 19
- Mixing with the omni 26
- Alternate omni setups 28
- Limited lifetime warranty 30
Похожие устройства
- Panasonic HDC-TM80EE-K Инструкция по эксплуатации
- Ariston Bravo M 7023 U-PV1 Инструкция по эксплуатации
- HP Pavilion p6621ru XS463EA Инструкция по эксплуатации
- Scarlett SC-219 Инструкция по эксплуатации
- Loewe Spheros R 32 HD+ Инструкция по эксплуатации
- Panasonic PT-DZ570E Инструкция по эксплуатации
- Polaris Stream Pro 5.3 Инструкция по эксплуатации
- JVC GZ-HM30B Инструкция по эксплуатации
- HP Pavilion Elite E410ru XJ004EA Инструкция по эксплуатации
- Scarlett SC-218 Инструкция по эксплуатации
- Loewe Spheros R 42 Инструкция по эксплуатации
- Panasonic PT-DW530E Инструкция по эксплуатации
- JVC GZ-HM446B Инструкция по эксплуатации
- HP Pavilion p6700ru LF969EA Инструкция по эксплуатации
- Loewe Viewvision DR+ Инструкция по эксплуатации
- Panasonic PT-DX500E Инструкция по эксплуатации
- Scarlett SC-217 Инструкция по эксплуатации
- HP Pavilion E-550ruLL444EA Инструкция по эксплуатации
- JVC GZ-HM446 Инструкция по эксплуатации
- Loewe Xelos A 20 Инструкция по эксплуатации