Braun 510 TexStyle 5 [10/78] F maintenance and cleaning
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Braun 510 TexStyle 5 [10/78] F maintenance and cleaning

Braun 510 TexStyle 5 [10/78] F maintenance and cleaning
10
F Maintenance and cleaning
To clean the sole plate, use steel wool.
Then wipe the sole plate clean with a cloth.
Never use a scourin
g pad, vinegar nor
other chemicals
. To clean the soft material
of handle and power shot and spray
buttons, use soapy water.
G Cleaning the anticalc valve
The iron’s anticalc valve is located at the
lower end of the steam button (3). It has
to be decalcified regularly (e.g. when the
steam development is insufficient).
Proceed as follows:
1) Unplug the iron and empty the water tank.
2) Press the steam button so it is lifted.
3) Remove carefully (some water may now
leak from the sole plate).
4) Do not touch the anticalc valve.
5) Immerse in vinegar (not vinegar essence)
or lemon juice until the lime becomes soft.
6) Use a non-metallic brush until all openings
are clean.
7) Rinse under running water.
8) Re-insert the steam button.
9) Press to check the steam on/off function.
Note:
the iron must never be used without
the steam button.
H Decalcifying /anticalc system
When scale particles come out of the steam
vents or when the steam development is
insufficient even after cleaning the anticalc
valve, you should clean the steam chamber
as follows:
1) Make sure the steam button is in its lower
position.
2)–3) Fill water into the tank, connect to the
mains and select the «•••» temperature
setting.
4)–5) Wait until the pilot light turns off.
Unplug the iron.
6)–7) Hold the iron over a sink, then press the
steam button so it is lifted, carefully pull it
up, turn it and rest it in this position.
Caution:
When the steam button is pulled
up, hot water and steam will come out from
the sole plate.
8) Push back the steam button until it catches
in the lower position.
9)–10) Fill water into the tank, connect to the
mains and select the «•••» temperature
setting.
11)–13) When the pilot light goes off, press
the power shot button 4 times to rinse the
iron. Disconnect the iron and wait for the
sole plate to cool off, then clean it as
described above in section «G».
Note:
the iron must never be used without
the steam button.
I Trouble-shooting guide
Problem Remedy
––––––––––––––––––––––––––––––––––––––
Drops Turn the steam regulator
coming out counter-clockwise to
of the steam reduce the steam or
vents press the steam button
to turn the steam off.
Take longer intervals
when pressing the power
shot button.
Select a higher tempera-
ture setting.
No steam Press the steam button
at all so that it is lifted.
Less steam Clean the anticalc valve
develops or (see «G»).
no steam at all
Calcium par- Decalcify the steam
ticles coming chamber (see «H»).
through the
steam vents
––––––––––––––––––––––––––––––––––––––
Subject to change without notice.
Please do not dispose of the
product in the household waste
at the end of its useful life. Disposal
can take place at a Braun Service
Centre or at appropriate collection
points provided in your country.
92263374_TS_540_S06-80 Seite 10 Montag, 2. April 2012 3:15 15

Содержание

Похожие устройства

F Maintenance and cleaning To clean the sole plate use steel wool Then wipe the sole plate clean with a cloth Never use a scouring pad vinegar nor other chemicals To clean the soft material of handle and power shot and spray buttons use soapy water G Cleaning the anticalc valve The iron s anticalc valve is located at the lower end of the steam button 3 It has to be decalcified regularly e g when the steam development is insufficient Proceed as follows 1 Unplug the iron and empty the water tank 2 Press the steam button so it is lifted 3 Remove carefully some water may now leak from the sole plate 9 10 Fill water into the tank connect to the mains and select the temperature setting 11 13 When the pilot light goes off press the power shot button 4 times to rinse the iron Disconnect the iron and wait for the sole plate to cool off then clean it as described above in section G Note the iron must never be used without the steam button I Trouble shooting guide Problem Remedy Drops coming out of the steam vents Turn the steam regulator counter clockwise to reduce the steam or press the steam button to turn the steam off Take longer intervals when pressing the power shot button Select a higher tempera ture setting 4 Do not touch the anticalc valve 5 Immerse in vinegar not vinegar essence or lemon juice until the lime becomes soft 6 Use a non metallic brush until all openings are clean 7 Rinse under running water 8 Re insert the steam button 9 Press to check the steam on off function Note the iron must never be used without the steam button H Decalcifying anticalc system When scale particles come out of the steam vents or when the steam development is insufficient even after cleaning the anticalc valve you should clean the steam chamber as fol lows 1 Make sure the steam button is in its lower position 2 3 Fill water into the tank connect to the mains and select the temperature setting 4 5 Wait until the pilot light turns off Unplug the iron 6 7 Hold the iron overasink then press the steam button so it is lifted carefully pull it up turn it and rest it in this position Caution When the steam button is pulled up hot water and steam will come out from the sole plate 8 Push back the steam button until it catches in the lower position 10 No steam Press the steam button at all so that it is lifted Less steam develops or no steam at all Calcium par ticles coming through the steam vents Clean the anticalc valve see G Decalcify the steam chamber see H Subject to change without notice Please do not dispose of the product in the household waste at the end of its useful life Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country

Скачать