Hamax 2017 Zenith Relax серо-черный — guide d'assemblage pour siège avec barre excentrique et support [7/17]

Содержание

• Hx_zenith_relax_carrier_bow_us_um_cover_2016 01 07 p.1
• Ok not ok p.1
• Zenith relax p.1
• User manual p.1
• Caution p.1
• Zenith relax p.2
• Main seat 2 restraint system 3 belt lock 4 foot rests 5 carrier bow 6 fastening bracket complete a bracket b metal strips c fastening screws d safety indicator 7 locking pin 8 reclining knob 9 footguard p.2
• Manuel de l utilisateur fr p.3
• Hx_zenith_relax_carrier_bow_us_um_spreads_2016 01 07 p.3
• Manual del usuario es p.4
• Remove the cable tie 11 by clipping them then remove the protection foam blocks 12 from the front and back both the cable tie and protection foam blocks are recyclable p.6
• Remove cable tie protective foam blocks p.6
• Press the front of the mounting bracket 6 to release the bracket from the transportation pins 13 remove the transportation pins the transportation pins 13 are recyclable p.6
• Zenith relax p.6
• Remove the transportation lock p.6
• Zenith relax p.7
• Turn the seat 1 upside down turn the locking pin 7 and push down the two snapfits before you pull the locking pin completely out p.7
• Remove locking pin p.7
• Mount the carrier bar to the seat p.7
• Insert the carrier bow 5 through the holes as shown below p.7
• Zenith relax p.8
• Place the fastening bracket 6a over the frame tube of the bike attach the bracket with the metal strips fastening screws 6b c do not tighten fully so that the height can be adjusted at a later stage p.8
• Locked 2 unlocked p.8
• Insert the locking pin 7 through the holes under the seat base keeping it in unlocked position to allow final adjustment later on p.8
• Insert locking pin p.8
• If there is a gear wire in the area where the metal strips 6b will be located the metal strips 6b may be placed between the wire and the frame tube p.8
• Fastening bracket p.8
• Guide the carrier bow ends 5 down into the bracket 6a until you hear a click locked position p.9
• Adjust the bracket 6a to the correct height until there is approx 10 12 cm between the rear wheel mudguard luggage carrier and the bicycle child seat p.9
• Zenith relax p.9
• Then tighten the four fastening screws 6c on the back of the bracket in the following pattern tighten and then re tighten p.9
• Suggested tightening torque is 10 nm this is however only a guideline if the bracket starts to move during use keep tightening until it is firmly fixed p.9
• Not fastened fastened p.9
• Mount the bicycle child seat onto the bracket p.9
• Make it a rule to check and if needed re tighten the bracket before every bicycle ride p.9
• Hamax fastening bracket make sure the carrier bow is correctly attached to the bracket by checking that the green safety indicators 7d are visible p.9
• Hamax fastening bracket p.9
• Zenith relax p.10
• Unlocked p.10
• Make sure the locking pin 7 is in the unlocked position before adjusting the seat to the correct lengthways position max 10 cm between the centre mark 14 on the seat and the rear hub after adjustment lock the seat by turning the locking pin 7 to locked position p.10
• Locked p.10
• How to release the foot rest 4 release the footrest handle on the back by flipping it upwards move the foot rest 4 to the preferred height and fasten the foot rest by pressing the foot rest handle down p.10
• Foot rest adjustment p.10
• Adjusting the seat p.10
• Extra footguard p.11
• Zenith relax p.11
• To mount the extra foot guard 9 press the foot guard into the fitting grooves until it clicks p.11
• Opposite view p.11
• How to fasten release the foot strap a to fasten the foot strap put the strap into the track and pull down to preferred length the strap will automatically lock it s only possible to tighten the strap when it is in the track to loosen the foot strap just pull it out of the track p.11
• Foot strap adjustment p.11
• Zenith relax p.12
• Where to push p.12
• The restraint system length can be adjusted by adjusting buckle a and b to adjust buckles a b hold the buckle as shown in pic 1 by pressing the red button the belt loosens by pulling the buckle upwards to tighten the restraint system just pull end of the belt straps pic 2 move the buckle c up to secure the belt so it cannot fall down from the child s shoulders pic 3 p.12
• The restraint system 2 can be attached and detached by pressing in or out the belt lock 3 shown in pic 1 it is important to press at the middle of the belt lock button pic 2 3 when detaching the restraint system the belt lock button needs an adult force to open this is for the safety of the child so they cannot open it p.12
• Restraint system p.12
• Pic 2 pic 3 p.12
• Chest buckle adjustment p.12
• To recline the seat press the reclining knob 9 down and at the same time twist to the required position p.13
• The seat 1 is easy to remove from the bicycle when not in use press the cover of the bracket and pull the seat bar free from the bracket 6 p.13
• Reclinable function p.13
• How to remove the seat p.13
• Zenith relax p.13
• Zenith relax p.14
• Warning check that the green safety indicators 6d of the bracket are visible ensure the rider and child always wear approved and properly fitted bicycle helmets never leave a child unattended in the bicycle child seat never leave a child in the bicycle child seat with the bicycle supported only by the kick stand p.14
• Before embarking on a bicycle trip p.14
• Adjust the restraint system 2 to ensure the child is snugly restrained in the seat adjust the foot rests 4 and fasten foot straps p.14
• Zenith relax p.15
• With an extra bracket 6 you can easily move one seat between two bicycles hamax fastening bracket 6 is available in two version standard and lockable art nr 604001 standard bracket art nr 604002 lockable bracket p.15
• Solution p.15
• Should your seat be too close to the carrier wheel when mounted there is an extra bar available which may solve your problem please contact your bicycle dealer p.15
• Problem solving p.15
• Problem p.15
• Extra fastening bracket p.15
• Zenith relax p.16
• You may also mount the seat on a bicycle luggage carrier by means of a carrier adapter this can be useful if your bicycle has a frame diameter outside the range of 28 40 mm or if you have an electrical bicycle p.16
• Read more about the carrier adapters at www hamax com child bike seat caress collection zenith with carrier adapter full assembly instructions follows the product when purchased and can also ble downloaded from www hamax com p.16
• Carrier adapter p.16