Home
Главная
Makita
Рубанок
DKP180Z
Инструкция по эксплуатации Страница: 7

Makita DKP180Z [7/84] Assembly

Switch action

Fig.4

CAUTION:

• Before installing the battery cartridge into the tool,

always check to see that the switch trigger

actuates properly and returns to the "OFF"

position when released.

• Do not pull the switch trigger hard without pressing

the lock-off lever. This can cause switch breakage.

To pr even t th e sw itch tr ig ger fro m bei ng ac ciden tal ly

pulled, a lock-off lever is provided. To start the tool, slide

the lock-off lever and pull the switch trigger. Release the

switch trigger to stop.

WARNING:

• For your safety, this tool is equipped with lock-off

lever which prevents the tool from unintended

starting. NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the

lock-off lever. Return tool a MAKITA service center

for proper repairs BEFORE further usage.

• NEVER tape down or defeat purpose and function

of lock-off lever.

To pr even t th e sw itch tr ig ger fro m bei ng ac ciden tal ly

pulled, a lock-off button is provided.

To s tar t th e to ol, dep re ss t he l ock -off b utto n an d pu ll t he

switch trigger. Release the switch trigger to stop.

Foot

Fig.5

After a cutting operation, raise the back side of the tool

and a foot comes under the level of the rear base. This

prevents the tool blades to be damaged.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Removing or installing planer blades

CAUTION:

• Tighten the blade installation bolts carefully when

attaching the blades to the tool. A loose installation

bolt can be dangerous. Always check to see they

are tightened securely.

• Handle the blades very carefully. Use gloves or

rags to protect your fingers or hands when

removing or installing the blades.

• Use only the Makita wrench provided to remove or

install the blades. Failure to do so may result in

overtightening or insufficient tightening of the

installation bolts. This could cause an injury.

For tool with conventional planer blades

Fig.6

Fig.7

Fig.8

To remove the blades on the drum, unscrew the

installation bolts with the socket wrench. The drum

cover comes off together with the blades.

To i nsta ll t he bla de s, f irst clean out all c hips or f or eig n matt er

adhering to the drum or blades. Use blades of the same

dimensions and weight, or drum oscillation/vibration will result,

causing poor planing action and, eventually, tool breakdown.

Place the blade on the gauge base so that the blade edge is

perfectly flush with the inside edge of the gauge plate. Place

the adjusting plate on the blade, then simply press in the

heel of the adjusting plate flush with the back side of the

gauge base and tighten two screws on the adjusting plate.

Now slip the heel of the adjusting plate into the drum groove,

then fit the drum cover on it. Tighten all the installation bolts

evenly and alternately with the socket wrench.

Repeat the above procedures for the other blade.

For tool with mini planer blades

Fig.9

Remove the existing blade, if the tool has been in use,

carefully clean the drum surfaces and the drum cover.

To remov e th e bla de s on the drum , uns cr ew th e th ree

installation bolts with the socket wrench. The drum

cover comes off together with the blades.

Fig.10

2. To install the blades, loosely attach the adjusting

plate to the set plate with the pan head screws

and set the mini planer blade on the gauge base

so that the cutting edge of the blade is perfectly

flush with the inside flank of the gauge plate.

Set the adjusting plate/set plate on the gauge base

so that the planer blade locating lugs on the set plate

rest in the mini planer blade groove, then press in the

heel of the adjusting plate flush with the back side of

the gauge base and tighten the pan head screws.

4. It is important that the blade sits flush with the inside

flank of the gauge plate, the planer blade locating

lugs sit in the blade groove and the heel of the

adjusting plate is flush with the back side of the

gauge base. Check this alignment carefully to ensure

uniform cutting.

5. Slip the heel of the adjusting plate into the groove

of the drum.

Fig.11

6. Set the drum cover over the adjusting plate/set

plate and screw in the three hex flange head bolts

so that a gap exists between the drum and the

set plate to slide the mini planer blade into

position. The blade will be positioned by the

planer blade locating lugs on the set plate.

7. The blade's lengthwise adjustment will need to be

manually positioned so that the blade ends are

Makita DKP180Z [7/84] Assembly

Содержание

Похожие устройства