Home
Главная
Makita
Рубанок
DKP180Z
Инструкция по эксплуатации Страница: 9

Makita DKP180Z [9/84] Maintenance

For tool with nozzle

Attach the elbow (optional accessory) on the nozzle of

the tool by just slipping on it. To r emo ve it , just p ull i t out .

OPERATION

Hold the tool firmly with one hand on the knob and the other

hand on the switch handle when performing the tool.

Planing operation

Fig.16

First, rest the tool front base flat upon the workpiece surface

without the blades making any contact. Switch on and wait

until the blades attain full speed. Then move the tool gently

forward. Apply pressure on the front of tool at the start of

planing, and at the back at the end of planing. Planing will

be easier if you incline the workpiece in stationary fashion,

so that you can plane somewhat downhill.

The speed and depth of cut determine the kind of finish.

The power planer keeps cutting at a speed that will not

result in jamming by chips. For rough cutting, the depth

of cut can be increased, while for a good finish you

should reduce the depth of cut and advance the tool

more slowly.

Shiplapping (Rabbeting)

Fig.17

To ma ke a s tep ped cut a s s how n in the f igu re, us e t he

edge fence (guide rule) which is obtained as accessory.

Fig.18

Draw a cutting line on the workpiece. Insert the edge

fence into the hole in the front of the tool. Align the

blade edge with the cutting line.

Fig.19

Adjust the edge fence until it comes in contact with the

side of the workpiece, then secure it by tightening the

screw.

Fig.20

When planing, move the tool with the edge fence flush

with the side of the workpiece. Otherwise uneven

planing may result.

Maximum shiplapping (rabbeting) depth is 9 mm.

Fig.21

You may wish to add to the length of the fence by

attaching an extra piece of wood. Convenient holes are

provided in the fence for this purpose, and also for

attaching an extension guide (optional accessory).

Chamfering

Fig.22

Fig.23

To mak e a cha mfe ring c ut as sho wn in the fi gur e, align

the "V" groove in the front base with the edge of the

workpiece and plane it.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or

the like. Discoloration, deformation or cracks may

result.

Sharpening the planer blades

For conventional blades only

Fig.24

Always keep your blades sharp for the best

performance possible. Use the sharpening holder

(optional accessory) to remove nicks and produce a fine

edge.

Fig.25

First, loosen the two wing nuts on the holder and insert

the blades (A) and (B), so that they contact the sides

Fig.26

Immerse the dressing stone in water for 2 or 3 minutes

before sharpening. Hold the holder so that the both

blades contact the dressing stone for simultaneous

sharpening at the same angle.

Replacing carbon brushes

Fig.27

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Fig.28

Fig.29

Use a screwdriver to remove the chip cover or nozzle.

Fig.30

Use a screwdriver to remove the brush holder caps.

Tak e o ut t he worn ca rbo n b rus hes, i nse rt t he n ew one s

and secure the brush holder caps.

To ma inta in pr odu ct SA FETY and REL IAB ILITY, re pa irs ,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers,

always using Makita replacement parts.

Makita DKP180Z [9/84] Maintenance

Содержание

Похожие устройства