![Vitamix Mix'n Machine Advance (VM025021-929) [6/14] General instructions](/img/pdf.png)
Vitamix Mix'n Machine Advance (VM025021-929) [6/14] General instructions
![Vitamix Mix'n Machine (VM025003-355) [6/14] General instructions](/views2/1340057/page6/bg6.png)
10
11
Notes: Should the cup be hard to hold, either move the agitator into the mix more
slowly or start with softer ice cream. Do not continue to operate if you are having
trouble holding the cup.
Both the permanent agitator and the removable agitator are designed to reduce
the possibility of damage when contacting a paper cup. However, they should not
be forced or held solidly against the side or bottom of the cup. The hard ice cream
agitator is specially designed to mix the product aggressively and thoroughly, so use
of a cup holder or sturdy cup is recommended to prevent the agitator from going
through the side of the cup.
7. Swirl the cup around the agitator to produce a pleasing product appearance and to
avoid leaving a hole in the center of the mixture. Before removing the cup, allow excess
mixture to be thrown o the agitator and be caught by the cup or lid/collar. Follow
machine shut-o instructions based on the specific model:
• For Mix’n Machine Advance Programmable Model:
The machine will shut o automatically at the end of
the programmed cycle. When the program is within 4
seconds of completion, the LED Indicator light will blink so
preparation can begin to remove the cup from the agitator.
The blinking light will get progressively faster to indicate
that the program cycle is almost complete and the machine
will shut o. This provides an indication, so that excess
product can be spun o the agitator. See Figure 5.
• For Mix’n Machine Advance Timer Model: The machine
will shut o automatically at the end of the preset time.
When the program is within 4 seconds of completion, the
LED Indicator light will blink so preparation can begin to
remove the cup from the agitator. The blinking light will get
progressively faster to indicate that the program cycle is
almost complete and the machine will shut o. This provides
an indication, so that excess product can be spun o the
agitator. See Figure 5.
• For Mix’n Machine Advance Variable Speed Model:
Press ON/OFF power switch to OFF to stop the
machine. See Figure 6.
• For Mix’n Machine Standard Model (Countertop
and Wall Mount): Press ON/OFF power switch to
OFF to stop the machine. See Figure 6.
8. Press the ON/OFF switch to OFF when not in use.
• To use the PULSE switch to refresh drinks and desserts (Advance
Programmable Model only): Make sure the power is ON. Move the cup under
the agitator and lift up so the agitator touches the bottom of the cup. Depress
the PULSE switch to start the agitator. With a swirling motion, gradually move the
cup up and down over the spinning agitator and completely around all sides of the
cup. Swirl the cup around the agitator to produce a pleasing product appearance
and to avoid leaving a hole in the center of the mixture. Before removing the cup,
allow excess mixture to be thrown o the agitator and be caught by the cup or
lid/collar. Release the switch to stop the agitator.
GENERAL INSTRUCTIONS
FIGURE 5
ON
OFF
FIGURE 6
PROGRAMMING
The Mix’n Machine Advance Programmable Model is pre-programmed with six blending
options. The Mix’n Machine Advance Timer Model is pre programmed with one pre-set
timed blending cycle. The programs can be customized by using a programming chip
or programmer software kit available from Vita-Mix Corporation. Call your distributor or
Customer Service for more information.
Although your machine comes from the factory pre-set with program(s), follow
these instructions when using a custom programming chip.
Programming with a Custom Chip
1. Turn the power to the machine ON using the
ON/OFF switch located on the front of the machine.
2. Facing the front of the machine, locate the
programming port on the right side panel.
Insert the custom programmed chip with the
silver contact bars up.
3. Within 5 seconds, the six PRE-SET PROGRAMS
will be re-programmed. The LED Indicator
light on the front of the machine will blink
when the program is accepted. If the LED
light does not blink, remove the programmed
chip and see note below.
4. Remove the programming chip, return it
to the original package and store in a safe,
easily accessible spot.
Resetting the Pre-Set Programs to the
Original Factory Settings
1. Turn the power to the machine OFF using the ON/OFF switch
located on the front of the machine.
2. Hold down the PULSE button while turning the power back
ON using the ON/OFF switch.
IMPORTANT NOTES!
PROGRAMMING CHIP: If the above programming steps are taken and the
LED light does not blink or the custom programming does not appear with
the first blend cycle, turn the chip 180° (side-to-side) and try again.
Programming Port
SIDE VIEW
Содержание
- All models 1
- Mix n machine 1
- Read and save these instructions 1
- Use and care manual 1
- Important notes 2
- Important safeguards 2
- Save these safety instructions 2
- Warnings 2
- Control panel 3
- Important notes 3
- Mix n machine advance programmable model 3
- Mix n machine advance timer model 3
- Control panel 4
- Important notes 4
- Mix n machine advance variable speed model 4
- Mix n machine standard model 4
- General instructions 5
- Mix n machine blending procedures 5
- Programmable model 5
- General instructions 6
- Important notes 6
- Programming 6
- Programming with a custom chip 6
- Resetting the pre set programs to the original factory settings 6
- Agitators 7
- Caution 7
- Important notes 7
- Splash guard 7
- Caring for your machine 8
- Housing 8
- Important notes 8
- Permanent agitators 8
- Removable reusable agitator 8
- Kits sold separately 9
- Mix n machine advance and mix n machine standard countertop models 9
- Parts list 9
- Kits sold separately 10
- Mix n machine standard wall mount model 10
- Parts list 10
- If you cannot fix your machine call vitamix technical support at 800 866 235 if outside the united states and canada contact your local vitamix distributor or telephone the vitamix international division at 1 440 782 450 or email international vitamix com for a distributor in your country 11
- Motor protection 11
- Possible actions 11
- Problem 11
- Problems 11
- The mix n machine is equipped with a reset breaker mounted on the motor enclosure see figures 1 and 2 should the motor be kept from turning locked rotor or otherwise be overloaded the breaker will trip if this occurs make sure the motor is free to rotate and wait a short period for it to cool down before pushing the reset breaker and restarting the motor never remove or bypass the reset breaker 11
- Troubleshooting 11
- Limited warrant 12
- Unless otherwise covered by contract 12
- Warranty 12
- What causes the warranty to be void 12
- What is covered under warranty 12
- What is not covered under warranty coverage exclusions 12
- When do the warranties apply coverage conditions 12
- How to obtain warranty coverage and repair 13
- How to ship the equipment for service 13
- Warranty 13
- Corporation commercial division 14
- Dimensions 14
- Motor speed and power requirements 14
- Products visit vitamix com 14
- Specifications 14
- To see the complete line of vitami 14
- Vita mi 14
- When applicable 14
Похожие устройства
- ATESY СР-Л-1-1200.600-02 Инструкция по эксплуатации
- ATESY СР-Л-1-1200.600-02 Презентация нейтрального оборудования ATESY 2-го поколения
- ATESY СР-Л-1-1200.600-02 Декларация о соответствии
- Abat ТМС-30НН-МЦ Инструкция по эксплуатации
- Abat ТМС-30НН-МЦ Паспорт на Abat ТМС-30НН-МЦ
- ATESY СКТС-Б-900-02 Инструкция по эксплуатации
- ATESY СКТС-Б-900-02 Презентация нейтрального оборудования ATESY 2-го поколения
- ATESY СКТС-Б-900-02 Декларация о соответствии ЕЭС
- ATESY СК-П-1500.800-02 Инструкция по эксплуатации
- ATESY СК-П-1500.800-02 Презентация нейтрального оборудования ATESY 2-го поколения
- ATESY СК-П-1500.800-02 Декларация о соответствии
- ATESY СР-С-2-700.700-02 Инструкция по эксплуатации
- ATESY СР-С-2-700.700-02 Презентация нейтрального оборудования ATESY 2-го поколения
- ATESY СР-С-2-700.700-02 Декларация о соответствии
- ATESY СКТ-С-600-02-Н Инструкция по эксплуатации
- ATESY СКТ-С-600-02-Н Презентация нейтрального оборудования ATESY 2-го поколения
- ATESY СКТ-С-600-02-Н Декларация о соответствии ЕЭС
- ATESY Ривьера 700 мм Инструкция по эксплуатации
- ATESY ШО-1 оцинк. сталь Инструкция по эксплуатации
- ATESY ШО-1 оцинк. сталь Декларация о соответствии ЕЭС