Home
Главная
Vitek
Весы Напольные
VT-1984 GY СЕРЫЙ
Инструкция по эксплуатации Страница: 4

Vitek VT-1984 GY СЕРЫЙ [4/28] English

ENGLISH

–

If there is a protective film on the scale surface,

remove it.

–

Clean the scale with a soft, slightly damp cloth

and then wipe it dry.

BATTERY INSTALLATION AND REPLACEMENT

–

Remove the battery compartment lid (7) and

insert 2 «AAA» batteries (supplied with the unit),

strictly following the polarity.

–

Place the battery compartment lid (7) back to

its place.

Note: If there is an isolation insert in the battery

compartment, remove the battery compartment lid

(7), remove the isolation insert and install the lid

back to its place.

Battery replacement

–

When the battery is low, the symbol «Lo» will

appear on the display (3).

–

Open the battery compartment lid (7), replace the

«AAA» batteries with new ones, strictly following

the polarity, and close the lid (7).

–

If you do not use the scale for a long time, remove

the batteries from the battery compartment.

WHAT IS EXCESS WEIGHT?

It is generally known that excessive body weight can

negatively affect health. Excess weight can cause

obesity, heart problems, facilitate atherosclerosis

and osteoporosis; but deficient body weight may

also lead to osteoporosis. (Osteoporosis is a sys-

temic skeleton disease characterized by reduced

bone density and impairment of bone tissue micro-

architectonics and leading to increased bone fra-

gility and risk of fracture by minimal trauma or even

without it).

Physical exercises and a moderate diet help to lose

excess weight and this scale will help to control your

weight.

It is known that in case of low weight muscles and

body tissues contain more water than fat. Electric

current passes through water better than through

fat. Sending weak current through the body, the

scale quickly and easily calculates the percentage of

fat and water in a human body. You can control your

weight relying on the results of the calculation.

RECOMMENDATIONS

–

Weigh yourself at the same time of the day.

–

It is recommended to measure fat and water per-

centage in the evening before supper.

–

At least 2-3 hours should pass after the meal.

–

At least 10-12 hours should pass after intensive

physical exercises.

–

Percentage of fat in the body depends on differ-

ent factors and can change during the day.

–

When calculating fat and water percentage of

children under 10 years of age, the results may

be inaccurate.

–

Professional sportsmen, people inclined to ede-

mas and people with nonstandard body propor-

tions can show inaccurate results of calculation.

Note: Fat, bone and muscle tissue and water

percentage can be calculated only if personal

data (sex, age, height) are entered correctly and

if you step on the scale barefoot.

SWITCHING ON

–

Place the scale on a flat solid surface; if the floor

is uneven or covered with a carpet or rug, the

weighing accuracy decreases.

–

The scale is switched on when a weight over 5 kg

is placed on the platform or by touching the «SET»

button (5).

MEASUREMENT UNITS SELECTION

–

Switch the scale on using one of the options

described above.

–

To select weight measurement units, press the

«UNIT» button (6) repeatedly.

–

Measurement units are shown on the display (3):

«kg» – weight is measured in kilograms;

«lb» – weight is measured in pounds;

«st:lb» – weight is measured in stones and

pounds.

WEIGHT MEASUREMENT

–

Step on the scale to switch it on.

–

Keep your feet parallel to each other and distrib-

ute your weight evenly.

–

Stay still while weighing. During weight measure-

ment the weight values will be flashing on the dis-

play (3), and after measurement they will glow

constantly.

Attention!

–

If a symbol «Err» appears on the display (3), it

means that the scale is overloaded. Step off

the scale immediately to avoid its damage.

–

The scale will be switched off automatically in

about 10 seconds after weight measurement.

ENTERING PERSONAL DATA (pic. 1)

–

Touch the «SET» button (5), one of the user num-

bers «P-01», «P-02».., «P-12» will be flashing on

the display.

–

Select the necessary user number using the but-

tons (4) «▲/▼» . You can enter data for 12 users.

Confirm your selection with the «SET» button (5).

VT-1984.indd 4 07.05.2014 17:22:00

Vitek VT-1984 GY СЕРЫЙ [4/28] English

Содержание

Похожие устройства