Ryobi LLCDI18022LX 18V LI H.DRILL EU 5133001898 [7/168] English

Ryobi LLCDI18022LX 18V LI H.DRILL EU 5133001898 [7/168] English
2
English
OPERATION
WARNING
Do not allow familiarity with products to make you
careless. Remember that a careless
second is sufficient to inflict serious injury.
of a fraction
WARNING
Always safety goggles or wear safety glasses
with side shields when operating products. Failure
to do so could result in objects being thro
your eyes, resulting in possible serious injury.
wn into
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or
not recommended can result in ser
injury.
APPLICATIONS
You may use this product for the purposes listed below:
Drilling in all types of wood products (lumber, plywood,
panelling, composition board, and hard board)
Drilling in ceramics, plastics, fiberglass, and laminates
Drilling in metals
Driving screws
Hammer drilling in concrete, brick, or other masonry
This product will accep
battery and packs
battery packs.
BATTERY PROTECTION FEATURES
RYOBI 18 V lithium-ion are designed with
features that protect the lithium-ion cells and maximiz
battery lif e. Under some
RYOBI
t RYOBI
built-in may cause the
powering to act
battery features
rom nickel-cadmium batteries.
During some application the batter
signal the batter
s,
differently f
operating
accessories
batteries
y to shut down, and cause the tool to
stop To reset the
trigger and resume normal operation.
NOTE: To prevent shut further of the avoid
forcing the tool.
If releasing the
down
battery
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
TO INSTALL BATTERY PACK
Lock the switch trigger by placing the rotation selector
in the center position.
Place the battery pack on the tool.
Make sure the latches on each side of the batter
trigger
running.
battery,
and the tool it is
conditions, these
One+ 18 V nickel-cadmium
One+ 18 V lithium-ion
does not reset the battery and
and tool, release the
y electronics may
ious personal
e
pack snap into place and the batter
on the tool before beginning operation.
y pack is secured
y
WARNING
Always remove battery pack from tool your when
you are
cleaning, or when not in use
assembling parts, making adjustments,
pack will pre
cause serious personal injury.
TO REMOVE BATTERY PACK
Lock the switch trigger by placing the rotation selector
in the center position.
Depress the latches on the side of battery pack.
Remove the battery pack from the tool.
vent accidental starting that could
. Removing battery
WARNING
Battery tools are always in operating condition.
Therefore, switch should be when locked
not in use or carrying at your side.
SWITCH TRIGGER
To turn the drill ON, depress the switch trigger.
To turn it OFF, release the switch trigger.
ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
The bit rotation is
selector located
held in operating position, the rotation selector
should be positioned to the left of the s
normal
above
reversible
always
the switch With the drill trigger.
and is controlled by a
forward drilling. The drilling direction is reversed when the
selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental star
not in use.
ting when
witch for trigger
VARIABLE SPEED
The switch trigger higher speed delivers variable
speeds
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
NOTE: You might hear a whistling or r
the use. Do not be concer switch during
inging noise from
normal part of the switch function.
ned; this is a
CAUTION:
To prevent gear damage, always allow the chuck
to come to a complete stop
direction of rotation.
To stop the dr
chuck to come to a complete stop.
before changing
ill, release the trigger and allo the w switch
the
See Figure 2.
See Figure 2.
See Figure 3.
See Figure 3.
EN
FR IT NL PT DA SV FI NO RU PL CS HU RO LV LT ET HR SL SK EL TRDE ES

Содержание

Похожие устройства

Скачать