Hotpoint-Ariston LST 53977 X [17/28] Advice regarding the first wash cycle

Hotpoint-Ariston LST 53977 X [17/28] Advice regarding the first wash cycle
EN
%
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain
duct with a minimum diameter of 4 cm. Alternatively, rest
it over a sink or tub; the free end of the hose should not
remain immersed in water.
The special plastic elbow
*
makes it easier to find the
best layout: fix the elbow to
the wall securely in order to
prevent the outlet hose from
moving and spilling the dirty
water.
The part of the hose marked
with the letter A should be
between 40 and 100 cm
above the ground (see figure).
We advise against the use of hose extensions.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
The socket is earthed and complies with current
regulations.
The socket can withstand the maximum load of the
appliance, which is indicated on the data plate
located on the inside of the door (see chapter entitled
Description of the appliance).
The power supply voltage falls within the values
indicated on the data plate on the inside of the door.
The socket is compatible with the plug of the
appliance. If this is not the case, ask an authorised
technician to replace the plug (see Assistance); do
not use extension cables or multiple sockets.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be re-
placed by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See As-
sistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not
observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick
the adhesive transparent strip under the wooden shelf in
order to protect it from any condensation which may
form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately
before running the first wash cycle, completely fill the
salt dispenser with water and add only then
approximately 1 kg of salt (see chapter entitled Rinse aid
and refined salt). The water may overflow: this is normal
and is not a cause for concern. Select the water
hardness value (see chapter entitled Rinse aid and
refined salt). - After the salt has been poured into the
machine, the LOW SALT indicator light
* switches off.
If the salt container is not filled, the water softener
and the heating element may be damaged as a result.
* Only available in selected models.
A
Technical data
Dimensions
width 44.5 cm
height 82 cm
depth 55 cm
Capacity
10 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage
See appliance data plate
Total absorbed
power
See appliance data plate
Fuse
See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-2006/95/EEC dated
16/01/2007
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE (Waste Electrical
and Electronic Equipment
WEEE)
AIO77
-

Содержание

Connecting the water outlet hose Anti condensation strip EN After installing the dishwasher open the door and stick Connect the outlet hose without bending it to a drain the adhesive transparent strip under the wooden shelf in duct with a minimum diameter of 4 cm Alternatively rest order to protect it from any condensation which may it over a sink or tub the free end of the hose should not form remain immersed in water The special plastic elbow Advice regarding the first wash cycle makes it easier to find the After the appliance has been installed immediately best layout fix the elbow to before running the first wash cycle completely fill the the wall securely in order to salt dispenser with water and add only then prevent the outlet hose from approximately 1 kg of salt see chapter entitled Rinse aid moving and spilling the dirty water and is not a cause for concern Select the water The part of the hose marked with the letter A should be hardness value see chapter entitled Rinse aid and refined salt After the salt has been poured into the between 40 and 100 cm machine the LOW SALT indicator light switches off and refined salt The water may overflow this is normal above the ground see figure is If the salt container is not filled the water softener K We advise against the use of hose extensions and the heating element may be damaged as a result Electrical connection Technical data Before inserting the plug into the electrical socket make sure that Dimensions width 44 5 cm height 82 cm depth 55 cm The socket is earthed and complies with current Capacity 10 standard place settings Water supply pressure 0 05 r 1 MPa 0 5 r 10 bar 7 25 145 psi Power supply voltage See appliance data plate Total absorbed power See appliance data plate Fuse See appliance data plate regulations The socket can withstand the maximum load of the appliance which is indicated on the data plate located on the inside of the door see chapter entitled Description of the appHancd The power supply voltage falls within the values indicated on the data plate on the inside of the door The socket is compatible with the plug of the appliance If this is not the case ask an authorised technician to replace the plug see Assistance do not use extension cables or multiple sockets K Once the appliance has been installed the power supply cable and the electrical socket should be easily C accessible ÎS The cable should not be bent or compressed AfO77 CT If the power supply cable is damaged it must be re placed by the manufacturer or its Technical Assistance Service in order to prevent all potential hazards See As sistance This dishwasher conforms to the following European Community Directives 2006 95 EEC dated 16 01 2007 Low Voltage and subsequent modifications 89 336 EEC dated 03 05 89 Electromagnetic Compatibility and subsequent modifications 97 17 EC Labelling 2002 96 CE Waste Electrical and Electronic Equipment WEEE CT The Company shall not be held responsible for any incidents that occur if these regulations are not observed Only available in selected models 17