Hotpoint-Ariston LST 53977 X [26/28] Troubleshooting
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hotpoint-Ariston LST 53977 X [26/28] Troubleshooting

Hotpoint-Ariston LST 53977 X [26/28] Troubleshooting
EN
$
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
Malfunction: Possible causes / Solutions:
The dishwasher does not start.
• The plug has not been inserted into the electrical socket properly, or there is
no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (see Start-up and use).
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water outlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes
excessive noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
The dishes and glasses are
streaked or have a bluish
tinge.
• The rinse aid dosage is too high.
The crockery has not been
dried properly.
• A wash cycle without a drying programme has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
• The rinse aid dispenser setting is not high enough.
The dishes are not clean.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not
been measured out correctly or it is not suitable for use in dishwashers
(see Start-up and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any water in/Tap shut-off
alarm.
(several short beeps are emitted)
(the ON/OFF indicator light flashes and
the number 6 appears on the display).
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when
the beeps sounded. Switch off the machine using the ON/OFF button, turn
on the tap and switch the machine back on after 20 seconds by pressing
the same button. Re-programme the machine and restart the wash cycle.
Water intake solenoid valve
malfunction alarm
(the ON/OFF indicator light flashes and
the number 2 appears on the display).
• Switch off the appliance by pressing the ON/OFF button and switch it back
on after one minute. If the alarm continues, shut off the water tap to
eliminate the risk of flooding, remove the plug from the electrical socket
and contact Assistance.
Water inlet hose alarm/Water inlet
filter blocked.
(the ON/OFF indicator light flashes and
the number 7 appears on the display).
• Switch off the appliance by pressing the ON/OFF button. Shut off the water
tap to eliminate the risk of flooding and remove the plug from the electrical
socket. Make sure the water inlet filter has not become blocked by various
impurities. (see “Care and maintenance” chapter).

Содержание

Похожие устройства

Troubleshooting Whenever the appliance fails to work check for a solution from the following list before calling for Assistance EN Malfunction Possible causes Solutions The dishwasher does not start The plug has not been inserted into the electrical socket properly or there is no power in the house The dishwasher door has not been shut properly A delayed start has been programmed see Start up and use No water drains out from the dishwasher The dishwasher cycle has not yet finished The water outlet hose is bent see Installation The drain duct is blocked The filter is clogged up with food residues The dishwasher makes excessive noise The dishes are rattling against each other or against the sprayer arms An excessive amount of foam has been produced the detergent has not been measured out correctly or it is not suitable for use in dishwashers see Start up and use The dishes and glasses are covered in a white film or limescale deposits The level of the refined salt is low or the dosage setting is not suited to the hardness of the water see Rinse aid and salt The lid on the salt dispenser is not closed properly The rinse aid has been used up or the dosage is too low The crockery is made from non stick material The dishes and glasses are streaked or have a bluish tinge The rinse aid dosage is too high The crockery has not been dried properly A wash cycle without a drying programme has been selected The rinse aid has been used up or the dosage is too low see Rinse aid and salt The rinse aid dispenser setting is not high enough The dishes are not clean The racks are overloaded see Loading the racks The crockery has not been arranged well The sprayer arms cannot move freely The wash cycle is too gentle see Wash cycles An excessive amount of foam has been produced the detergent has not been measured out correctly or it is not suitable for use in dishwashers see Start up and use The lid on the rinse aid compartment has not been shut correctly The filter is dirty or blocked see Care and maintenance The refined salt level is low see Rinse aid and salt The dishwasher does not take any water in Tap shut off alarm several short beeps are emitted the ON OFF indicator light flashes and the number 6 appears on the display There is no water in the mains supply The water inlet hose is bent see Installation Turn on the tap and the appliance will start after a few minutes The appliance lock has been activated because no action was taken when the beeps sounded Switch off the machine using the ON OFF button turn on the tap and switch the machine back on after 20 seconds by pressing the same button Re programme the machine and restart the wash cycle Water intake solenoid valve malfunction alarm the ON OFF indicator light flashes and the number 2 appears on the display Switch off the appliance by pressing the ON OFF button and switch it back on after one minute If the alarm continues shut off the water tap to eliminate the risk of flooding remove the plug from the electrical socket and contact Assistance Water inlet hose alarm Water inlet filter blocked the ON OFF indicator light flashes and the number 7 appears on the display Switch off the appliance by pressing the ON OFF button Shut off the water tap to eliminate the risk of flooding and remove the plug from the electrical socket Make sure the water inlet filter has not become blocked by various impurities see Care and maintenance chapter 26

Скачать