Hitachi 93199692 [10/50] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hitachi 93199692 [10/50] English

Hitachi UC18YRL [10/50] English
9
English
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger
after use, and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an
extended period is not activated, the electric
discharge might be low when using them the first
and second time. This is a temporary phenomenon,
and normal time required for recharging will be
restored by recharging the batteries 2-3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the
electric current, the battery may be damaged and
its life will become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the
battery and recharge it after it has cooled for a
while.
CAUTION
䡬 If the battery is charged while it is heated because
it has been left for a long time in a location subject
to direct sunlight or because the battery has just
been used, the overheat lamp of the charger lights
up green. In such a case, first let the battery cool,
then start charging.
䡬 When the charge status flickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects
in the charger’s battery installation hole. If there are
no foreign objects, it is probable that the battery
or charger is malfunctioning. Take it to your
authorized Service Center.
䡬 Since the built-in micro computer takes about 3
seconds to confirm that the battery being charged
with UC18YRL / UC18YFL is taken out, wait for a
minimum of 3 seconds before reinserting it to
continue charging. If the battery is reinserted within
3 seconds, the battery may not be properly charged.
MAINTENANCE AND INSPECTION
1. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
2. Cleaning of the charger
When the charger is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do
not use chloric solvents, gasoline or paint thinner,
for they melt plastics.
3. Store idle charger
When not in use, the charger should be stored in
dry, high or locked-up place — out of reach of
children.
4. Service parts list
A : Item No.
B : Code No.
C : No. Used
D : Remarks
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.

Содержание

Похожие устройства

English 4 Disconnect the charger s power cord from the receptacle 5 Hold the charger firmly and pull out the battery NOTE Be sure to pull out the battery from the charger after use and then keep it Regarding electricdischarge In case of new batteries etc As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated the electric discharge might be low when using them the first and second time This is a temporary phenomenon and normal time required for recharging will be restored by recharging the batteries 2 3 times How to make the batteries perform longer _____________ 1 Recharge the batteries before they become completely exhausted When you feel that the power of the tool becomes weaker stop using the tool and recharge its battery If you continue to use the tool and exhaust the electric current the battery may be damaged and its life will become shorter 2 Avoid recharging at high temperatures A rechargeable battery will be hot immediately after use If such a battery is recharged immediately after use its internal chemical substance will deteriorate and the battery life will be shortened Leave the battery and recharge it after it has cooled for a while CAUTION O If the battery is charged while it is heated because it has been left for a long time in a location subject to direct sunlight or because the battery has just been used the overheat lamp of the charger lights up green In such a case first let the battery cool then start charging O When the charge status flickers in red at 0 2 seconds intervals check for and takeout any foreign objects in the charger s battery installation hole If there are no foreign objects it is probable that the battery or charger is malfunctioning Take it to your authorized Service Center O Since the built in micro computer takes about 3 seconds to confirm that the battery being charged with UC18YRL UC18YFL is taken out wait for a minimum of 3 seconds before reinserting it to continue charging If the battery is reinserted within 3 seconds the battery may not be properly charged MAINTENANCE AND INSPECTION 1 Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened Should any of the screws be loose retighten them immediately Failure to do so could result in serious hazard 2 Cleaning of the charger When the charger is stained wipe with a soft dry cloth or a cloth moistened with soapy water Do not use chloric solvents gasoline or paint thinner for they melt plastics 9 3 Store Idle charger When not in use the charger should be stored in dry high or locked up place out of reach of children 4 Service parts list A Item No B Code No C No Used D Remarks CAUTION Repair modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance In the operation and maintenance of power tools the safety regulations and standards prescribed in each country must be observed MODIFICATIONS Hitachi Rower Tools are constantly being improved and modified to incorporate the latest technological adv ancem ents Accordingly some parts i e code numbers and or design may be changed without prior notice NOTE Due to HITACHI S continuing program of research and development the specifications herein are subject to change without prior notice

Скачать