Makita TD111DZ 185160 [7/52] Assembly
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Makita TD111DZ 185160 [7/52] Assembly

Makita TD111DZ 185160 [7/52] Assembly
7 ENGLISH
Changing the impact force
►Fig.7: 1. Hard 2. Soft 3.Amode4. Changed in three
steps 5. Button
Youcanchangetheimpactforceinthreesteps:hard,
soft,andAmode.
Thisallowsatighteningsuitabletothework.
Everytimethebuttonispressed,thenumberofblows
changes in three steps.
“Amode(assistmode)”isaneasy-to-usemodefor
driving screws with good control.
In this mode, the tool drives a screw with low-speed
rotationatrst.Afterthetoolstartstoimpact,therota-
tionspeedincreasesandreachesthemaximumspeed.
Forapproximatelyoneminuteafterreleasingtheswitch
trigger, the impact force can be changed.
Impact force grade displayed
on panel
Maximum blows Purpose Example of application
Hard
3,900 min
-1
(/min) Tighteningwhenforceand
speed are desired.
Tighteningwoodscrews,
tightening bolts.
Soft
1,600 min
-1
(/min) Tighteningwithlessforceto
avoid screw thread breakage.
Tighteningsashscrews,tight-
ening small screws such as M6.
Amode
3,900 min
-1
(/min) Tighteningscrewswithbetter
control.
Tighteninglongscrews.
NOTE:Amodeisavailableonlywhenthetoolrotatesclockwise.WhenrotatingcounterclockwiseinAmode,the
impact force and speed are the same as hard mode.
NOTE:Whenalllampsontheswitchpanelgoout,thetoolisturnedofftosavethebatterypower.Theimpactforce
gradecanbecheckedbypullingtheswitchtriggertotheextentthatthetooldoesnotoperate.
NOTE:Whilepullingtheswitchtrigger,theimpactforcegradecannotbechanged.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
socket bit
Optional accessory
►Fig.8
Useonlydriverbit/socketbitthathasinsertingportionshown
inthegure.Donotuseanyotherdriverbit/socketbit.
For tool with shallow driver bit hole
A=12mm
B=9mm
Use only these type of driver
bit. Follow the procedure
1. (Note) Bit-piece is not
necessary.
For tool with deep driver bit hole
A=17mm
B=14mm
Toinstallthesetypesofdriver
bits, follow the procedure 1.
A=12mm
B=9mm
Toinstallthesetypesofdriver
bits, follow the procedure 2.
(Note) Bit-piece is necessary
for installing the bit.
1. Toinstallthedriverbit,pullthesleeveinthedirec-
tion of the arrow and insert the driver bit into the
sleeve as far as it will go.
Thenreleasethesleevetosecurethedriverbit.
►Fig.9: 1. Driver bit 2. Sleeve
2.
Toinstallthedriverbit,pullthesleeveinthedirection
of the arrow and insert the bit-piece and driver bit into
thesleeveasfarasitwillgo.Thebit-pieceshouldbe
inserted into the sleeve with its pointed end facing in.
Thenreleasethesleevetosecurethedriverbit.
►Fig.10: 1. Driver bit 2. Bit-piece 3. Sleeve
Toremovethedriverbit,pullthesleeveinthedirection
of the arrow and pull the driver bit out.
NOTE:
If the driver bit is not inserted deep enough into the
sleeve, the sleeve will not return to its original position and
the driver bit will not be secured. In this case, try re-insert-
ing the bit according to the instructions above.
NOTE:Afterinsertingthedriverbit,makesurethatit
isrmlysecured.Ifitcomesout,donotuseit.
Installing hook
►Fig.11: 1. Groove 2. Hook 3. Screw
Thehookisconvenientfortemporarilyhangingthetool.
Thiscanbeinstalledoneithersideofthetool.Toinstall
the hook, insert it into a groove in the tool housing on
eithersideandthensecureitwithascrew.Toremove,
loosen the screw and then take it out.

Содержание

Похожие устройства

Скачать