Fluke 707 ex Информация о калибровке онлайн
PN 2086601 May 2003 Rev. 2, 5/09
© 2003, 2009 Fluke Corporation, All rights reserved. Printed in U.S.A. Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
1
®
707Ex
mA Calibrator
Calibration Information
XW Warning
Read Safety Information before using the mA Calibrator.
Introduction
The Calibration Information for the 707Ex mA
Calibrator (hereafter referred to as the mA Calibrator)
provides the information necessary to verify the
performance and adjust the calibration of the mA
Calibrator.
This document includes the following:
• Contacting Fluke
• Specifications
• Safety Information
• Maintenance
• User-Replaceable Parts
• Recommended Test Equipment
• Performance Verification
• Calibration Adjustment
For complete operating instructions, refer to the
707Ex Users Manual located on the CD that came
with the mA Calibrator.
Warranty
This Fluke product comes with a 3-year warranty for
material and workmanship. For warranty information,
refer to the 707Ex Users Manual that came with the
mA Calibrator.
Contacting Fluke
To contact Fluke, call one of the following telephone
numbers:
• Technical Support USA: 1-800-44-FLUKE (1-
800-443-5853)
• Calibration/Repair USA: 1-888-99-FLUKE (1-
888-993-5853)
• Canada: 1-800-36-FLUKE (1-800-363-5853)
• Europe: +31 402-675-200
• Japan: +81-3-3434-0181
• Singapore: +65-738-5655
• Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.fluke.com
.
To register your product, visit
http://register.fluke.com.
To view, print, or download the latest manual
supplement, visit
http://us.fluke.com/usen/support/manuals
.
Address correspondence to:
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
Содержание
- Calibration information 1
- Contacting fluke 1
- Introduction 1
- Ma calibrator 1
- Warranty 1
- Accuracy specifications 2
- General specifications 2
- Safety information 2
- Applying a voltage greater than 28 v to the input of the ma calibrator invalidates its ex approval and may impair its safe operation in an ex hazardous area 3
- Correct certification is illegible 3
- Damage sustained in transit 3
- Do not carry additional batteries within the ex hazardous area 3
- Do not open the ma calibrator 3
- Do not remove or install the battery within the ex hazardous area 3
- Do not use the ma calibrator in an ex hazardous area unless it is completely and securely fitted in its accompanying red holster 3
- Exposure to excessive loads 3
- External damage to the housing 3
- Faults and damage 3
- Functioning errors occur 3
- Functioning errors or obvious measurement inaccuracies occur which prevent further measurement by the ma calibrator 3
- If there is any reason to suspect that the safe operation of the ma calibrator has been affected it must be immediately withdrawn from use and precautionary measures must be taken to prevent any further use of the ma calibrator in an ex hazardous area 3
- Incorrect storage of the unit 3
- Internal damage to the ma calibrator 3
- Permitted limitations are exceeded 3
- Safety information 3
- Safety regulations 3
- The safety features and integrity of the unit may be compromised by any of the following 3
- The use of this 707ex ma calibrator meets the requirements of the regulations providing that the user observes and applies the requirements as laid down in the regulations and that improper and incorrect use of the unit is avoided 3
- Use must be restricted to the specified application parameters 3
- Use only type tested batteries the use of any other battery will invalidate the ex certification and present a safety risk refer to table 2 3
- Using the product with the red holster removed 3
- Xw warning 3
- Xw warnings and cautions 3
- Maintenance 4
- Symbols 4
- A message from 5
- Fluke corporation 5
- Static awareness 5
- Do not remove or install the battery within the ex hazardous area 7
- Insert the replacement battery and re install the battery door make sure it is securely in place 7
- Lift off the battery door on the back of the ma calibrator as shown 7
- Press d to turn the ma calibrator off 7
- Remove the battery 7
- Remove the red holster 7
- Remove the test leads from the input terminals 7
- Remove the test probes from the input signal 7
- Replacing the battery 7
- Return the ma calibrator to its red holster 7
- To avoid false readings which could lead to electric shock or injury replace the battery as soon as m low battery indicator appears on the display 7
- To replace the battery refer to figure 1 and table 2 7
- Use only a single 9 v alkaline battery properly installed to power the ma calibrator see table 2 7
- User replaceable parts 7
- User replaceable parts and accessories are shown in figure 2 and table 1 7
- Xw warning 7
- Performance verification 8
- Recommended test equipment 8
- Calibration adjustment 9
Похожие устройства
- Fluke 707 ex Приложение к паспорту безопасности
- Fluke 707 ex Паспорт безопасности
- Fluke 707 ex Приложение к Руководству по эксплуатации
- Fluke 705 Дополнение к информации о калибровке
- Fluke 705 Приложение к Инструкции
- Fluke 705 Приложение к паспорту безопасности
- Fluke 705 Паспорт безопасности
- Fluke 705 Loop Calibrators Data Sheet
- Fluke 705 Информация о калибровке
- Fluke 707 Приложение к паспорту безопасности
- Fluke 707 Паспорт безопасности
- Fluke 754 DPC TRACK _ Руководство по установке
- Fluke 754 Приложение к руководству по калибровке
- Fluke 754 Calibration and documentation for process manufacturing_ Costs, benefits and feasibility
- Fluke 754 DPCTrack2 _ Начало работы
- Fluke 754 Положение об энергозависимости памяти
- Fluke 754 750 Series Brochure
- Fluke 754 DPC TRACK _ Руководство по эксплуатации
- Fluke 754 Pressure Calibration APPLICATIONS AND SOLUTIONS
- Fluke 754 Приложение к Руководству по эксплуатации