Vitek VT-1212 [6/10] Русский

Vitek VT-1212 [6/10] Русский
ЧИСТКА И УХОД
После каждого использования:
1. Установите переключатель
“STEAM/DRY” в положение “DRY”.
2. Отключите утюг от сети.
3. Удалите всю оставшуюся воду из емкости.
Храните утюг на основе!
ЧИСТКА ПОДОШВЫ
После каждого использования протирайте подошву влажной
мягкой тканью. Если на ней остались следы прилипшей ткани,
прогладьте горячим утюгом влажную ткань из хлопка. В случае
сильного загрязнения используйте специальные очистители. Не
используйте для чистки абразивные жесткие средства.
ЧИСТКА СЪЕМНОГО ПАРОВОГО КЛАПАНА
Очищайте съемный клапан, если функция парового глажения
плохо работает. Для этого:
1. Убедитесь, что утюг отключен от сети.
2. Удалите воду из емкости и поставьте утюг на подошву.
3. Установите переключатель
“STEAM/DRY” сначала в положение
“DRY”, а затем!в положение “CLEAN” до щелчка.
4. Снимите клапан и прочистите его с мылом стальной щеточкой.
5. Установите клапан на место. Сопоставьте отметку “CLEAN” с
индикатором на ручке. Вращайте по часовой стрелке до
положения “DRY”.
СПЕЦИФИКАЦИЯ
Питание 230 В ~ 50Гц
Максимальная мощность 1200 Вт
СРОК СЛУЖБЫ УТЮГА НЕ МЕНЕЕ 3Х ЛЕТ
РУССКИЙ
15
the maximum water level is reached. Push the water inlet cover firmly
to close.
NOTE: The special soleplate design allows you to use tap water with your
Ultura iron without affecting the steam performance. However in very
hard water areas, Sunbeam recommend the use of distilled water, or
water which has been demineralised.
For best performance, we recommend the use of Sunbeam Water Klean,
available from Sunbeam Service Centres. This will produce up to 30 litres
of demineralised water.
Do not fill the iron with fabric conditioner, starches or any other
solution as these will damage the steam mechanism. Do not use
contaminated water.
Dry Ironing
1. Insert the 3 pin plug into a 230 volt power outlet and turn the power on.
The Power ON Light (positioned on top of the handle) will illuminate to
indicate that the iron is ON.
2. Turn the Temperature Dial to the desired setting by aligning the setting
on the dial with the temperature indicator light.
3. Select DRY on the STEAM/DRY Dial. This will cut off the steam flow if
there is water in the tank.
Steam Ironing
1. Insert the plug into the power outlet and turn the power on.
2. Turn the Temperature Dial to any of the temperatures within the steam
band.
3. Turn the STEAM/DRY Dial to the desired steam setting.
Using the Shot of Steam
The Shot of Steam can be used whether DRY or STEAM ironing when the
Temperature Dial is set within the steam band.
1. Ensure the tank is at least V4 full of water.
2. Select the desired temperature.
3. Press the shot of steam button several times with the iron on the sole!
plate to prime the pump.
NOTE: If the tank has run dry, it may be necessary to re!prime the pump
after filling the iron with water.
ENGLISH
6
1212.qxd 03.07.03 16:50 Page 12

Содержание

Скачать