LG DK379 [54/60] Additional information

LG DK379 [54/60] Additional information
24
Additional Information
Last Condition Memory
This player memorizes the user settings for the last disc
that you have viewed. Settings remain in memory even
if you remove the disc from the player or switch off the
player. If you load a disc that has its settings memo-
rized, the latest stop position is automatically recalled.
Notes
Settings are stored in memory for use any time.
This player does not memorize settings of a disc if
you switch off the player before commencing to play
it.
Screen Saver
The screen saver picture appears when you leave the
DVD Player in stop mode for about five minutes.
After the Screen Saver has been engaged for about five
minutes, the DVD Player will automatically turn itself off.
Controlling the TV
Your remote control is capable of operating your DVD
player as well as limited functions of LG TV.
Follow the instructions below to operate for your LG TV.
11
Before using the remote control, press the DVD or
TV button to select the device to be operated.
To switch the remote control mode (to operate a dif-
ferent device), be sure to press the DVD or TV
button first.
22
The POWER, PR./CH.(
EE
/
DD
), VOL (
11
/2), MUTE and
TV AV buttons on remote control are used to oper-
ate the LG TV.
Setting Remote Control Codes for LG TV
This remote control supports two remote control
codes for LG TV: Code 1 and Code 2.
When the unit is shipped from the factory, the remote
control is set to Code 1.
To set the remote control to Code 2, hold down both
the TV button and the number 2 button on the
remote control. (If the batteries in the remote control
are replaced while the remote control is set to Code
2, the setting will revert to Code 1.)
To set the remote control back to Code 1, hold down
both the TV button and the number 1 button on the
remote control.
Note
If the remote control does not operate your particular
TV, try the other code or use the remote control original-
ly supplied with the LG TV.
Due to the variety of codes used by manufacturers,
OUR COMPANY cannot guarantee that the remote con-
trol will operate every model of LG TV.
Video Mode Setting
With certain discs, the playback picture may be flickering
or Dot Crawl is shown on straight lines. That means
Vertical interpolation or De-interlace is not perfectly
matched with the disc. In this case, the picture quality
may be improved by changing the video mode.
To change the video mode, press and hold DISPLAY
about 3 seconds during disc playback. The new video
mode number selected is displayed on the TV screen.
Check whether the video quality has improved. If not,
repeat the above procedure until picture quality is
improved.
Video mode change sequence:
MODE1 MODE2 MODE3 MODE1
If you turn off the power, the video mode will be back
to initial state (MODE1).
Detailed Descriptions for Video Modes
MODE1: The source material of the DVD video (film material or
video material) is determined from disc information.
MODE2: Suitable for playing film based content or video based
material recorded by the progressive scan method.
MODE3: Suitable for playing video based content with compar-
atively little motion.
Note
The video mode setting only works when the Progressive
Scan mode is set to Onin the Setup menu.
HDCD Playback
HDCD is a process that increases the fidelity of both spe-
cially encoded HDCD discs and standard CD audio discs.
When an HDCD-encoded disc is playing, the special
decoder is automatically activated and the HDCD Indicator
lights. No user intervention is required.
To enjoy the benefits of HDCD, your DVD Player must be
connected to your A/V receiver via the Analog Audio
Outputs. However, if your A/V receiver or surround proces-
sor is equipped with built-in HDCD decoding and Digital
Audio Output mode is set to Stream/PCM on the Setup
menu, you may also use a Coaxial or Optical digital audio
connection so that the HDCD processing is done there.
System Select
You must select the appropriate system mode for your TV
system. If NO DISC appears in the display window, press
and hold PAUSE on the front panel for more than 5 sec-
onds to be able to select a system (PAL, NTSC, or AUTO).
When the selected system does not coincide with the
system of your TV, normal color picture may not be
dis
played.
AUTO: Select when DVD player is connected with Multi
system TV.
NTSC: Select when DVD player is connected with
NTSC-TV.
PAL: Select when DVD player is connected with PAL-
TV.
VCD1.1VCD2.0
DVD-ADVD-V
VCD1.1
CD
DVD-ADVD-V

Содержание

Скачать