![Fluke 724 Инструкция по эксплуатации онлайн [31/56] 4956](/img/pdf.png)
Fluke 724 Инструкция по эксплуатации онлайн [31/56] 4956
![Fluke 724 Инструкция по эксплуатации онлайн [31/56] 4956](/views2/1005521/page31/bg1f.png)
Temperature Calibrator
Using Measure Mode
21
Table 5. Thermocouple Types Accepted
Type Positive Lead
Positive Lead (H)
Color Negative Lead Specified Range
Material
ANSI* IEC**
Material (°C)
E Chromel Purple Violet Constantan -200 to 950
N Ni-Cr-Si Orange Pink Ni-Si-Mg -200 to 1300
J Iron White Black Constantan -200 to 1200
K Chromel Yellow Green Alumel -200 to 1370
T Copper Blue Brown Constantan -200 to 400
B Platinum (30 % Rhodium) Gray Platinum (6 % Rhodium) 600 to 1800
R Platinum (13 % Rhodium) Black Orange Platinum -20 to 1750
S Platinum (10 % Rhodium) Black Orange Platinum -20 to 1750
L Iron Constantan -200 to 900
U Copper Constantan -200 to 400
*American National Standards Institute (ANSI) device negative lead (L) is always red.
**International Electrotechnical Commission (IEC) device negative lead (L) is always white.
Содержание
- February 2000 rev 8 03 1
- Temperature calibrator 1
- Users manual 1
- Limited warranty limitation of liability 2
- Table of contents 3
- Title page 3
- Temperature calibrator contents 5
- List of tables 7
- Table title page 7
- Figure title page 9
- List of figures 9
- Contacting fluke 11
- Introduction 11
- Temperature calibrator 11
- Safety information 13
- Standard equipment 13
- Warning 14
- Caution 15
- Warning 15
- Alligator clips 16
- Figure 1 standard equipment 16
- Stackable test leads 16
- Tl75 test lead set 16
- Users manual 16
- Zi01f eps 16
- 6 5 4 3 2 18
- Figure 2 input output terminals and connectors 18
- Figure 2 shows the calibrator input and output terminals table 3 explains their use 18
- Getting acquainted with the calibrator 18
- Input and output terminals 18
- Source 18
- Tc rtd 18
- Users manual 18
- Figure 3 keys 20
- Figure 3 shows the calibrator keys and table 4 explains their use 20
- Users manual 20
- Display 23
- Getting started 24
- Shut down mode 24
- Figure 5 voltage to voltage test 25
- Recall 25
- Source 25
- Tc rtd 25
- Temperature calibrator shut down mode 25
- Zi04f eps 25
- Contrast adjustment 26
- Current measurement with loop power 27
- Measuring electrical parameters upper display 27
- Using measure mode 27
- Figure 8 connections for supplying loop power 28
- Source 28
- Tc rtd 28
- Users manual 28
- Measuring electrical parameters lower display 29
- Measuring temperature 30
- Using thermocouples 30
- Figure 10 measuring temperature with a thermocouple 32
- Process temperature 32
- Tc miniplug 32
- Users manual 32
- Warning 30 v maximum to 32
- Using resistance temperature detectors rtds 33
- Figure 11 measuring temperature with an rtd measuring 2 3 and 4 wire resistance 35
- Resistance to be measured 35
- Temperature calibrator using measure mode 35
- Sourcing electrical parameters 36
- Using source mode 36
- Simulating rtds 37
- Simulating thermocouples 37
- Color depends on type of tc 38
- Figure 13 connections for simulating a thermocouple 38
- Source 38
- Tc miniplug 38
- Tc rtd 38
- Users manual 38
- Figure 14 connections for simulating 3 wire rtd 39
- Recall 39
- Sensor terminals 39
- Source 39
- Tc rtd 39
- Temperature calibrator using source mode 39
- Manually stepping the output 40
- Setting 0 and 100 output parameters 40
- Stepping and ramping the output 40
- Auto ramping the output 41
- Storing and recalling setups 41
- Calibrating a transmitter 42
- Figure 15 calibrating a thermocouple transmitter 43
- Source 43
- Tc rtd 43
- Temperature calibrator calibrating a transmitter 43
- Testing an output device 44
- Is good problems while measuring using the right jacks indicate that f3 may have opened to replace the fuse refer to figure 17 and perform the following steps 45
- Replacing the batteries 45
- Replacing the fuse 45
- The fuse can be removed and checked for resistance a value of 10 45
- Turn the calibrator off remove the test leads from the terminals and hold the calibrator face dow 45
- Warning 45
- Cleaning the calibrator 46
- Maintenance 46
- Service center calibration or repair 46
- Replacement parts 47
- Figure 18 replacement parts 48
- Users manual 48
- Dc ma measurement 49
- Dc voltage measurement 49
- Dc voltage source 49
- Specifications 49
- Ohms measurement 50
- Ohms source 50
- Millivolt measurement and source 51
- Temperature thermocouples 51
- Temperature rtd ranges and accuracies its 90 52
- General specifications 53
- Loop power supply 53
Похожие устройства
- Condtrol UBEXI XC 500 D Инструкция по эксплуатации
- Centurion XP v.1 Инструкция по эксплуатации
- LG MH-6354G Инструкция по эксплуатации
- Belkin F8N372cwBKW Инструкция по эксплуатации
- Digitech RP80 Инструкция по эксплуатации
- Candy GOY 1054 L-07 Инструкция по эксплуатации
- Fluke 725 Инструкция по эксплуатации
- Telwin Superior Plasma 60 HF 400V Инструкция по эксплуатации
- Centurion BIKE KEEPER Инструкция по эксплуатации
- Digitech S100 Инструкция по эксплуатации
- LG MH-6352U Инструкция по эксплуатации
- Candy GO4 107 DF 07 Инструкция по эксплуатации
- Fluke 725 ex Инструкция по эксплуатации
- Telwin SUPERPlasma 80/3 HF Инструкция по эксплуатации
- LG MH-6352T Инструкция по эксплуатации
- Digitech S200 Инструкция по эксплуатации
- Belkin F8N337cw Black Инструкция по эксплуатации
- Centurion BIKE Инструкция по эксплуатации
- Candy GO4 1064 D 07S Инструкция по эксплуатации
- Fluke 726 Инструкция по эксплуатации